Steering System

Steering column

In this manual: Steering System
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~4min read

Exploded View

1. Cover

1. Cover
2. Sub-harness
3. Band
4. Steering column assembly 5. Slide plate (inner)
6. Slide plate (outer)
7. Bracket

disassembly. Always replace after every
disassembly.

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
Removal and Installation: N·m (kg-m, in-lb)


Removal and Installation

REMOVAL

CAUTION:
• While removing the steering column assembly, never unlock the tilt lever. • Never impact on the axis when removing steering column assembly. • Be careful when removing steering column assembly from the vehicle because it is heavy. • Keep steering column assembly away from magnetic sources. • Never disassemble steering column assembly. It is not separable. • While removing the steering column assembly, never move the steering gear.

• When removing the steering column assembly, be careful not to allow the intermediate shaft to turn

.

1. Set vehicle to the straight-ahead position. 2. Place the tilt to the lowest level. 3. Remove instrument lower panel. Refer to IP-13, "Removal and Installation". 4. Remove driver air bag module. Refer to SR-13, "Removal and Installation". 5. Remove steering wheel. Refer to ST-9, "Removal and Installation". 6. Remove steering column cover. Refer to IP-13, "Removal and Installation". 7. Remove spiral cable. Refer to SR-16, "Removal and Installation". 8. Remove combination switch. Refer to BCS-162, "Removal and Installation". (without intelligent key system) or BCS-94, "Removal and Installation" (with intelligent key system). 9. Disconnect each switch harness connectors installed to steering column assembly.

10. Remove intermediate shaft mounting bolt (steering column side), and separate intermediate shaft from steering column assembly. Refer to ST-14, "Removal and Installation".

CAUTION:
• Place a matching mark on both intermediate shaft and steering column assembly before removing intermediate shaft.

• When removing intermediate shaft, never insert a tool, such as a screwdriver, into the yoke groove to pull out the intermediate shaft. In case of the violation of the above, replace intermediate shaft with a new one.

11. Disconnect EPS control unit connectors. 12. Remove steering column assembly. CAUTION:
When removing the mounting, be careful not to drop the steering column assembly.

13. Remove slide plate (outer and inner) from steering column assembly.

14. Remove cover, sub-harness, band, and bracket from steering column assembly.

CAUTION:
Remove cover, sub-harness, band, and bracket only when necessary.

15. Perform inspection after removal. Refer to ST-11, "Inspection".

INSTALLATION

CAUTION:
• Never impact on the axis when removing steering column assembly.

• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.

Note the following, and install in the reverse order of removal.

• After tightening mounting nut (A) of the steering column assembly, press in slide plate (outer and inner) (1) to tighten mounting nut (B).

CAUTION:
The slide plate must be securely pressed in before tightening the nut of slide plate (outer and inner).

• For intermediate shaft mounting bolt direction, refer to ST-13, "Exploded View". (Do not insert it from the other side.)

• When connecting intermediate shaft upper side (1) and column

• When connecting intermediate shaft upper side (1) and column shaft, make sure the bolt is securely seated in groove (A) of column shaft (A) before final tightening. • After installing steering column assembly, perform self-diagnosis with CONSULT-III to ensure correct operation. Refer to STC-10, "CONSULT-III Function". • Never reuse band.

• Perform inspection after installation. Refer to ST-11, "Inspection".

Inspection

Inspection

INSPECTION AFTER REMOVAL

• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any abnormal conditions.

• Measure steering column assembly rotating torque using a preload gauge (A) (SST: ST3127S000). Replace steering column assembly if the rotating torque is outside the standard.

Rotating torque : Refer to ST-23, "Steering Column Operating Range".

• Measure the length “L” shown in the figure, if vehicle has been

• Measure the length “L” shown in the figure, if vehicle has been involved in a minor collision. Replace steering column assembly (with motor, reduction gear, sensor) if “L” is outside the standard.

L : Refer to ST-23, "Steering Column Operating Range".

INSPECTION AFTER INSTALLATION

INSPECTION AFTER INSTALLATION

• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any abnormal conditions. • Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel turning angle. Refer to ST-8, "Inspection".

• Check tilt mechanism operating range “T” shown in the figure.

T : Refer to ST-23, "Steering Column Operating Range".

Steering shaft