Exterior Lighting System Halogen type

System

In this manual: Exterior Lighting System Halogen type
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~15min read

Headlamp system

HEADLAMP SYSTEM : System Diagram
HEADLAMP SYSTEM : System Description

HEADLAMP SYSTEM : System Description

OUTLINE

Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and relay control function of IPDM E/R.

HEADLAMP (LO) OPERATION

• BCM detects the combination switch condition with the combination switch reading function.

• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the headlamp (LO) ON condition.

Headlamp (LO) ON condition - Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment) - Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON

• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low beam request signal.

HEADLAMP (HI) OPERATION

• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communication according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request signal.

Headlamp (HI) ON condition - Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
- Lighting switch AUTO, with the front fog lamp switch ON, the ignition switch ON and lighting switch HI.

• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.

• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high beam request signal.

FOLLOW ME HOME FUNCTION

When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow me home function of BCM.

• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits the low beam request signal for a period of time to IPDM E/R through CAN communication.

Follow me home ON condition - Ignition switch OFF
- Lighting switch OFF

• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low beam request signal.

• When in any of following conditions, follow me home function can be cancelled while follow me home function is operating.

Follow me home OFF condition - Ignition switch is turned from OFF→ACC or ON - Lighting switch is turned from OFF→ON

NOTE:
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during operation of follow me home function. • Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass operation, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approximately 120 seconds (flash-to-pass operation, 4 times).

• Follow me home function activating time can be set by CONSULT-III. Refer to EXL-20, "HEADLAMP : CONSULT- III Function (BCM - HEAD LAMP)"(with Intelligent Key), EXL-25, "HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)"(without Intelligent Key).

HEADLAMP SYSTEM : Fail-Safe

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

Auto light system (without DTRL)

Auto light system (without DTRL)

AUTO LIGHT SYSTEM (WITHOUT DTRL) : System Di
AUTO LIGHT SYSTEM (WITHOUT DTRL) : System Description

AUTO LIGHT SYSTEM (WITHOUT DTRL) : System Description

OUTLINE

• Auto light system is controlled by each function of BCM and IPDM E/R.

Control by BCM
- Combination switch reading function - Headlamp control function - Auto light function

Control by IPDM E/R
- Relay control function • Auto light function turns the exterior lamps* ON/OFF automatically according to the outside brightness.

*: Headlamp (LO/HI), parking, license plate and tail lamps (Headlamp HI depends on the combination switch condition.) license plate lamp

AUTO LIGHT FUNCTION

• BCM detects the combination switch condition with the combination switch reading function. • BCM detects the engine condition by the engine status signal received from ECM via CAN communication. • BCM receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain sensor serial link. • BCM judges the ON/OFF status of the exterior lamp according to ON/OFF requests from light & rain sensor and the vehicle condition.

• BCM transmits each request signal to IPDM E/R via CAN communication according to ON/OFF condition by the auto light function.

NOTE

:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT-III. Refer to EXL-20, "HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".

Auto light system (with DTRL)

AUTO LIGHT SYSTEM (WITH DTRL) : System Diagram
AUTO LIGHT SYSTEM (WITH DTRL) : System Description

AUTO LIGHT SYSTEM (WITH DTRL) : System Description

OUTLINE

• Auto light system is controlled by each function of BCM and IPDM E/R.

Control by BCM
- Combination switch reading function - Headlamp control function - Auto light function

Control by IPDM E/R
- Relay control function • Auto light function turns the exterior lamps* ON/OFF automatically according to the outside brightness.

*: Headlamp (LO/HI), parking lamp, tail lamp (Headlamp HI depends on the combination switch condition.) AUTO LIGHT FUNCTION

• BCM detects the combination switch condition with the combination switch reading function. • BCM detects the engine condition by the engine status signal received from ECM via CAN communication. • BCM receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain sensor serial link. • BCM judges the ON/OFF status of the exterior lamp according to ON/OFF requests from light & rain sensor and the vehicle condition.

• BCM transmits each request signal to IPDM E/R via CAN communication according to ON/OFF condition by the auto light function.

NOTE

:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT-III. Refer to EXL-20, "HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".

Daytime running light system

DAYTIME RUNNING LIGHT SYSTEM : System Diagram
DAYTIME RUNNING LIGHT SYSTEM : System Description

DAYTIME RUNNING LIGHT SYSTEM : System Description

OUTLINE

• Turns the following exterior lamps ON as the daytime running light.

- Headlamp (LO)
- Parking, license plate and tail lamps.

• Daytime running light is controlled by daytime running light control function and combination switch reading function of BCM, and relay control function of IPDM E/R.

DAYTIME RUNNING LIGHT OPERATION

• BCM detects the combination switch condition by the combination switch reading function. • BCM detects vehicle condition depending on the following signals.

- Engine status signal (received from ECM via CAN communication) • BCM transmits the low beam request signal and daytime running light request signal to IPDM E/R via CAN communication according to the daytime running light ON condition.

Daytime running light ON condition - Engine running
- Lighting switch OFF
- Auto light switch is ON, front fog lamp switch and rear fog lamp switch are OFF, and auto light judgement is OFF.

• IPDM E/R turns the integrated headlamp low relay and daytime running light relay ON according to the low beam request signal and daytime running light request signal. And it turns each lamps ON.

Headlamp aiming control (manual)

HEADLAMP AIMING CONTROL (MANUAL) : System Description

The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor integrated in the front combination lamp.

Front fog lamp system

FRONT FOG LAMP SYSTEM : System Diagram
FRONT FOG LAMP SYSTEM : System Description

FRONT FOG LAMP SYSTEM : System Description

OUTLINE

Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM, and relay control function of IPDM E/R.

FRONT FOG LAMP OPERATION

• BCM detects the combination switch condition by the combination switch reading function.

• BCM transmits the front fog lights request signal to IPDM E/R and the combination meter via CAN communication according to the front fog lamp ON condition.

Front fog lamp ON condition - Front fog lamp switch ON and any of the followings.

• Lighting switch 1ST
• Lighting switch 2ND
• Lighting switch AUTO and the ignition switch ON

IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front fog lights request signal.

Combination meter turns the front fog lamp indicator lamp ON according to the front fog lights request signal.

FRONT FOG LAMP SYSTEM : Fail-Safe

CAN COMMUNICATION CONTROL When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

Rear fog lamp system

Rear fog lamp system

REAR FOG LAMP SYSTEM : System Diagram
REAR FOG LAMP SYSTEM : System Description

REAR FOG LAMP SYSTEM : System Description

OUTLINE

Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function of BCM.

REAR FOG LAMP OPERATION

• BCM detects the condition of the combination switch by the combination switch reading function.

• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.

Rear fog lamp switch is turned from OFF to ON with any of following condition.

- Lighting switch 2ND
- Lighting switch AUTO and the ignition switch ON - Front fog lamp ON

• BCM transmits the rear fog lamp status signal to the combination meter using CAN communication.

• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal.

Turn signal and hazard warning lamp system

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description

OUTLINE

Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the flasher control function of BCM.

TURN SIGNAL LAMP OPERATION

• BCM detects the combination switch condition by the combination switch reading function.

• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn signal switch is in the right (left) position. BCM blinks the turn signal lamp.

HAZARD WARNING LAMP OPERATION

BCM supplies voltage to both turn signal lamp circuit when the hazard switch is ON. BCM blinks the hazard warning lamp.

TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION

• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication while the turn signal lamp and the hazard warning lamp are operating.

• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal indicator lamp according to the turn signal indicator lamp signal.

3-TIME FLASHER FUNCTION

• By a short touch of the turn signal lever, BCM blinks the turn signal lamps 3 times in the selected direction.

• Cancel the operation when short touch of the turn signal lever in the reverse direction during the 3-time flasher function operating.

HIGH FLASHER OPERATION

• BCM detects the turn signal lamp circuit status from the current value.

• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating.

NOTE

:
The blinking speed is normal while operating the hazard warning lamp.

Parking, license plate and tail lamp system (without DTRL)

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : System Diagram
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : System

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : System Description

OUTLINE

Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp control function of BCM, and relay control function of IPDM E/R.

PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION

• BCM detects the combination switch condition by the combination switch reading function.

• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communication according to the ON/OFF condition of the parking, license plate and tail lamps.

Parking, license plate and tail lamps ON condition - Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment - Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON

• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON according to the position light request signal.

• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : Fail-Safe

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

Parking, license plate and tail lamp system (with DTRL)

Parking, license plate and tail lamp system (with DTRL)

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : System Diagram
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : System

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : System Description

OUTLINE

Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp control function of BCM, and relay control function of IPDM E/R.

PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION

• BCM detects the combination switch condition by the combination switch reading function.

• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communication according to the ON/OFF condition of the parking, license plate and tail lamps.

Parking, license plate and tail lamps ON condition - Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment - Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the daytime running light relay ON and turns the parking, license plate and tail lamps ON according to the position light request signal.

• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.

PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : Fail-Safe

CAN COMMUNICATION CONTROL

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With BCM

Exterior lamp battery saver system (without DTRL)

Exterior lamp battery saver system (without DTRL)

EXTERIOR LAMP BATTERY SAVER SYSTEM (WITHOUT DTRL) : System Diagram
EXTERIOR LAMP BATTERY SAVER SYSTEM (WITHOUT DTRL) : System Description

EXTERIOR LAMP BATTERY SAVER SYSTEM (WITHOUT DTRL) : System Description

OUTLINE

• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.

Control by BCM
- Combination switch reading function - Headlamp control function - Exterior lamp battery saver function

Control by IPDM E/R
- Relay control function

• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when the ignition switch is turned OFF with the exterior lamps ON.

*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp EXTERIOR LAMP BATTERY SAVER ACTIVATION

BCM turns the exterior lamps OFF (battery saver is activated) when all of following condition.

• Exterior lamps ON
• When any of the following conditions is satisfied.

- Driver side door switch is turned from OFF to ON while ignition switch is OFF.

- Ignition switch is turned from ON to OFF while driver side door switch is ON.

NOTE

:
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.

• Lighting switch ON→ OFF → ON

Exterior lamp battery saver system (with DTRL)

EXTERIOR LAMP BATTERY SAVER SYSTEM (WITH DTRL) : System Diagram
EXTERIOR LAMP BATTERY SAVER SYSTEM (WITH DTRL) : System Description

EXTERIOR LAMP BATTERY SAVER SYSTEM (WITH DTRL) : System Description

OUTLINE

• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.

Control by BCM
- Combination switch reading function - Headlamp control function - Exterior lamp battery saver function

Control by IPDM E/R
- Relay control function

• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when the ignition switch is turned OFF with the exterior lamps ON.

*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp EXTERIOR LAMP BATTERY SAVER ACTIVATION

BCM turns the exterior lamps OFF (battery saver is activated) when all of following condition.

• Exterior lamps ON
• When any of the following conditions is satisfied. - Driver side door switch is turned from OFF to ON while ignition switch is OFF.

- Ignition switch is turned from ON to OFF while driver side door switch is ON.

NOTE

:
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.

• Engine running
• Lighting switchON→ OFF → ON