Camera Aiming Adjustment
Description
Always adjust the camera aiming after removing and installing or replacing the lane camera unit.
Preparation
PERFORM SELF-DIAGNOSIS
CONSULT
Perform self-diagnosis of lane camera unit.
Is any DTC detected?
Except “C1B01-54”>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to DTC Description.
“C1B01-54” or no DTC>>GO TO 2.
PREPARATION BEFORE CAMERA AIMING ADJUSTMENT
Perform pre-inspection for diagnosis. Refer to Work Procedure.
Adjust the tire pressure to the specified pressure value.
Maintain no-load in Nissan Murano vehicle.
Check if coolant and engine oil are filled up to correct level and fuel tank is full.
Shift the selector lever to “P” position and release the parking brake.
Clean the windshield.
Completely clear off the instrument panel.
GO TO 3.
PREPARATION OF J-52266-2 ALIGNMENT TARGET
Prepare the alignment target according to the following procedure and the figure.
Attach the J-52266-2 alignment target to a movable board.


Board 
String 
Cone 
Center between two targets Side of a target (Ts) : 120 mm (4.72 in) Height of a target lower end (Htl) : 1,180 mm (46.46 in) Height of a target center (Ht) : 1,300 mm (51.18 in) Height of a target upper end (Htu) : 1,420 mm (55.91 in) Width between a right target center from a left target center (Dbt) : 720 mm (28.35 in) W1 : 180 mm (7.09 in) W2 : 180 mm (7.09 in)
Proceed to Target Setting.
Target Setting
TARGET SETTING

| A – E (C – F) | : 3,000 mm (118.11 in) |
Mark points “A”, “B”, “C” and “D”at the center of the lateral surface of each wheels.

Draw line “LH” passing through points “A” and “B” on the left side of Nissan Murano vehicle.
Mark point “E” on the line “LH” at the positions 3,000 mm (118.11 in) from point “A”.
Draw line “RH” passing through points “C” and “D” on the right side of Nissan Murano vehicle in the same way as step 2.
Mark point “F” on the line “RH” at the positions 3,000 mm (118.11 in) from point “C”.
Draw line “FW” passing through the points “E” and “F” on the front side of Nissan Murano vehicle.
Mark point “X” at the center of point “E” and “F” on the line “FW”.
Center the J-52266-2 alignment target at point “X” facing the Nissan Murano vehicle.

Dt : 3,000 mm (118.11 in)
Proceed to Camera Aiming Adjustment.
Camera Aiming Adjustment
CHECK VEHICLE HEIGHT
Measure the wheelarch height.

| Hfl: Front left wheelarch height [mm] | |
| Hfr: Front right wheelarch height [mm] |
GO TO 2.
CAMERA AIMING ADJUSTMENT
CONSULT
Select “Work Support” on “LANE CAMERA”.
Select “AUTO AIM”.
Confirm the following items;
The target should be accurately placed.
The Nissan Murano vehicle should be stopped.
Select “Start” to perform camera aiming.
Input the following parameters, and then select “Start”.
Hfl : Measured value Hfr : Measured value Nissan Murano Vehicle Reference Value : 706 mm VP : 0 mm Dt : 3,000 mm Dbt : 720 mm Htu : 1,420 mm Htl : 1,180 mm Ts : 120 mm Confirm the displayed item.
“Normally Completed”: Select “Completion”.
“SUSPENSION”, “ABNORMALLY COMPLETED”: Perform the following services.
Displayed item Possible cause Service procedure SUSPENSION — Temporary malfunction in internal processing of the lane camera unit. Go back to step 1. 00H Routine not activated Lane camera unit malfunction. Position the target appropriately again.
Then perform the aiming again.10H Writing error Temporary malfunction in internal processing of the lane camera unit.
Lane camera unit malfunction.
ABNORMALLY COMPLETED 2 Lane camera unit cannot detect the target
A target is not-yet-placed.
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
Position the target appropriately again.
Then perform the aiming again.3 Roll angle is outside the threshold
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
4 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
5 Input value of aiming is invalid.
Input value is not correct against actual setting position.
Correct input value of aiming and perform camera aiming again. 6 The size of target is different. (A numerical value input to CONSULT differs from detected size)
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
Position the target appropriately again.
Then perform the aiming again.7 The size of target is different. (A numerical value input to CONSULT differs from detected size)
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
8 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
9 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
10 Detect several targets.
The position of the targets is not correct.
The position of the lane camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Murano vehicle condition.
Input value is not correct against actual setting position.
11 Internal process malfunction Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNOMALLY COMPLETED again after aiming, replace lane camera unit.
12 Internal process time out Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNOMALLY COMPLETED again after aiming, replace lane camera unit.
13 Waiting for the start or aiming. (Insufficient passage of time from key SW ON to the start of aiming.)
Inappropriate work environment.
Position the target appropriately again.
Then perform the aiming again.14 Configuration of the lane camera unit is not completed. Complete the configuration of the lane camera unit.
Refer to Work Procedure.
Then turn the ignition switch OFF→ON Then position the target appropriately again.Ignition switch is not turned OFF→ON after the configuration of the lane camera unit is completed. Turn the ignition switch OFF→ON. Then position the target appropriately again. 15 Writing process malfunction Check self-diagnosis result. If DTC is detected, perform trouble diagnosis.
Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNOMALLY COMPLETED again after aiming, replace lane camera unit.
16 Internal transmitting malfunction 19 Unit internal malfunction 20 Writing value malfunction If lane camera unit is already replaced, perform configuration
Position the target appropriately again. Then perform the aiming
If there is still malfunction after performing above procedure, replace lane camera unit.
22 Unit internal malfunction Check self-diagnosis result. If DTC is detected, perform trouble diagnosis.
Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNOMALLY COMPLETED again after aiming, replace lane camera unit.
58 Unit internal malfunction Check self-diagnosis result. If DTC is detected, perform trouble diagnosis.
Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNOMALLY COMPLETED again after aiming, replace lane camera unit.
59 Unit internal malfunction 60 Unit internal malfunction 61 Unit internal malfunction 62 Unit internal malfunction 63 No aiming done Turn the ignition switch OFF→ON Then position the target appropriately again.
Confirm that “Normally completed” is displayed and then select “End” to close the adjustment procedure.
GO TO 3.
PERFORM SELF-DIAGNOSIS
CONSULT
Perform self-diagnosis of “LANE CAMERA”.
Is any DTC detected?
YES>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to DTC Index.
NO>>GO TO 4.
ACTION TEST
Perform the LDW/I-LI system action test. Refer to Work Procedure for LANE DEPARTURE WARNING or INTELLIGENT LANE INTERVENTION
Check that the LDW and I-LI systems operate normally.
Work End.