Maintenance

Cvt Fluid

4steps
~24min
5/5difficulty
Done 0 of 4
Inspection

FLUID LEAKAGE

  • Check transaxle surrounding area (oil seal and plug etc.) for fluid leakage.

  • If transaxle appears to have oil seepage or a leak, follow the steps below to assist in a correct diagnosis.

  1. Thoroughly clean off the area of the suspected leak.

  2. Insert 1 fluid ounce of Fluorescent Oil Dye into CVT.

    Tool number : — (J-52990)

  3. Drive Nissan Murano vehicle for a minimum of 10 minutes.

  4. Inspect for leaks with A/C Dye Kit.
    Tool number : — (J-43926)
CVT Fluid Level Check

INSPECTION

Park the vehicle on a level surface with the engine running and parking brake set.

Using CONSULT, ensure that the CVT fluid temperature is between 170°F to 180°F (77°C to 82°C).

Shift the transmission into REVERSE for 5 seconds.

Shift the transmission into DRIVE for 5 seconds.

Shift the transmission into REVERSE for 5 seconds.

Shift the transmission into PARK.

Remove cap (A) using tool.

Tool : (J-52611)

With the Nissan Murano vehicle in PARK and the engine running, insert Tool into the CVT fluid pipe.

Tool : (J-51155)

Tool : (J-51155)

Inspect Tool to determine the CVT fluid level.

Tool : (J-51155)
CVT fluid level : 14 – 22 mm (0.55 – 0.86 in)

ADJUSTMENT

Adjust the fluid level from the bottom of the CVT using the charge pipe. Refer to Adjustment.

Replacement
CVT fluid : Refer to Fluids and Lubricants.
Fluid capacity : Refer to Fluids and Lubricants.

Select “Data Monitor” in “TRANSMISSION” using CONSULT.

Select “FLUID TEMP” and confirm that the CVT fluid temperature is 40 °C or less.

Check that the selector lever is in the “P” position, then completely engage the parking brake.

Lift up the Nissan Murano vehicle.

Remove the drain plug and drain the CVT fluid from the oil pan. Refer to Exploded View.

Install the drain plug to oil pan.

Remove the overflow plug from converter housing.

: Nissan Murano Vehicle front

Install the charging pipe set (CVT stand pipe adapter kit) KV311039S0 (J-52584) (A) into the drain hole.

Install the ATF changer hose (B) to the charging pipe.

Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT fluid.

Remove the ATF changer hose and charging pipe, then install the overflow plug.

Lift down the Nissan Murano vehicle.

Start the engine.

While depressing the brake pedal, shift the selector lever to the entire position from “P” to “D”, and shift it to the “P” position.

Check that the CONSULT “Data Monitor” in “FLUID TEMP” is 35 °C to 45 °C.

Stop the engine.

Lift up the Nissan Murano vehicle.

Remove the drain plug, and then drain CVT fluid from oil pan.

Repeat steps 8 to 18 (one time).

Tighten the drain plug to the specified torque. Refer to Exploded View.

Remove the overflow plug.

Install the charging pipe set (CVT stand pipe adapter kit) KV311039S0 (J-52584) into the overflow plug hole.

Install the ATF changer hose to the charging pipe.

Fill approximately 3 liter (3-1/8 US qt, 2-5/8 lmp qt) of the CVT fluid.

Remove the ATF changer hose and charging pipe, then install the overflow plug.

Lift down the Nissan Murano vehicle.

Start the engine.

While depressing the brake pedal, shift the selector lever to the entire position from “P” to “D”, and shift it to the “P” position.

Check that the CONSULT “Data Monitor” in “FLUID TEMP” is 35 °C to 45 °C.

Lift up the Nissan Murano vehicle.

Remove the overflow plug and confirm that the CVT fluid is drained from the overflow plug hole.

When the flow of CVT fluid slows to a drip, tighten the overflow plug to the specified torque. Refer to Exploded View.

Lift down the Nissan Murano vehicle.

Select “Data Monitor” in “TRANSMISSION” using CONSULT.

Select “CONFORM CVTF DETERIORTN”.

Select “Erase”.

Stop the engine.

Adjustment
CVT fluid : Refer to Fluids and Lubricants.
Fluid capacity : Refer to Fluids and Lubricants.

Check that the selector lever is in the “P” position, then completely engage the parking brake.

Start the engine.

Adjust the CVT fluid temperature to be approximately 40 °C.

While depressing the brake pedal, shift the selector lever to the entire position from “P” to “L”, and shift it to the “P” position.

Lift up the Nissan Murano vehicle.

Check that there is no CVT fluid leakage.

Remove the overflow plug from converter housing.

: Nissan Murano Vehicle front

Install the charging pipe set (CVT stand pipe adapter kit) KV311039S0 (J-52584) (A) into the overflow plug hole.

Install the ATF changer hose (B) to the charging pipe.

Fill approximately 0.5 liter (1/2 US qt, 1/2 lmp qt) of the CVT fluid.

Remove the ATF changer hose from the charging pipe, and check that the CVT fluid drains out from the charging pipe. If it does not drain out, perform charging again.

When the flow of CVT fluid slows to a drip, remove the charging pipe from the converter housing.

Tighten the overflow plug to the specified torque. Refer to Exploded View.

Lift down the Nissan Murano vehicle.

Stop the engine.