Driver Information & Multimedia

Diagnosis System (sonar Control Unit)

~3min read
CONSULT Function

APPLICATION ITEMS

CONSULT can display each diagnostic item using the diagnostic test modes shown as follows:

Direct Diagnostic ModeDescription
ECU Identification The sonar control unit part number is displayed.
Self Diagnostic Result The sonar control unit self diagnostic results are displayed.
Data Monitor The sonar control unit input/output data is displayed in real time.
Active Test The sonar control unit activates outputs to test components.
Work Support The settings for sonar control unit functions can be changed.
Configuration
  • The Nissan Murano vehicle specification can be read and saved.

  • The vehicle specification can be written when replacing sonar control unit.

CAN Diag Support Mntr The result of transmit/receive diagnosis of CAN communication is displayed.

ECU IDENTIFICATION

Displays the part number of sonar control unit.

SELF-DIAGNOSTIC RESULTS

For details, refer to DTC Index.

DATA MONITOR

Monitor ItemDescription
Nissan Murano Vehicle SPEED [mph/km/h] Indicates vehicle speed signal received from combination meter on CAN communication line.
SONAR C/U POWER SUPPLY [V] Indicates condition of supply voltage signal to sonar control unit.
SENSOR VOLTAGE [V] Indicates condition of voltage signal to sonar sensors.
DETECTION MODE [Mode 1/Mode 2/Mode 3] Indicates condition of display detection mode.
SW OPRT AFTR IGN ON [Yes/No] Indicates condition of switch operation after ignition ON signal.
SONAR TEMPORARY OFF [Yes/No] Indicates condition of sonar system.
SONAR PERMANENT OFF [Yes/No] Indicates condition of sonar system.
P N RANGE [On/Off] Indicates condition of selector lever P (park) or N (neutral) position.
LED [On/Off] Indicates condition of LED.
TRAILER CONNECT [CON/N CON Indicates if trailer is connected.
REVERSE RANGE [On/Off] Indicates condition of transmission range switch R (reverse) position.
SHRT DST FRM RR SENS [cm/in] Indicates distance to obstacle.
SHRT DST FRM FR SENS [cm/in]
COR[RL] [cm/in]
COR[RL]→ CEN[RL]/CEN[R] [cm/in]
CEN[RL]/CEN[R]→ COR[RL] [cm/in]
CEN[RL]/CEN[R] [cm/in]
CEN[RL]→ CEN[RR] [cm/in]
CEN[RR]→ CEN[RL] [cm/in]
CEN[RR] [cm/in]
CEN[RR]/CEN[R]→ COR[RR] [cm/in]
COR[RR]→ CEN[RR]/CEN[R] [cm/in]
COR[RR] [cm/in]
COR[FL] [cm/in]
COR[FL]→ CEN[FL]/CEN[F] [cm/in]
CEN[FL]/CEN[F]→ COR[FL] [cm/in]
CEN[FL]/CEN[F] [cm/in]
CEN[FL]→ CEN[FR] [cm/in]
CEN[FR]→ CEN[FL] [cm/in]
CEN[FR] [cm/in]
CEN[FR]/CEN[F]→ COR[FR] [cm/in]
COR[FR]→ CEN[FR]/CEN[F] [cm/in]
COR[FR] [cm/in]
RVRB TIME COR[RL] [ms/sec]
RVRB TIME COR[RR] [ms/sec]
RVRB TIME CEN [RL] [ms/sec]
RVRB TIME CEN [RR] ms/sec]
RVRB TIME COR[FL] [ms/sec]
RVRB TIME COR[FR] [ms/sec]
RVRB TIME CEN [FL] [ms/sec]
RVRB TIME CEN [FR] ms/sec]
FRONT BUZZER [Off/On] Indicates condition of buzzer.
REAR BUZZER [Off/On]
ATTENUATION TIME SIDE[RL] [ms] Indicates condition of attenuation time.
ATTENUATION TIME SIDE[RR] [ms]
Synchronization state [try/not try] Indicates condition of synchronization state.
High side switch counter [numerical] Indicates high side switch counts.

ACTIVE TEST

Test ItemDescription
FRONT BUZZER This test is able to check sonar buzzer operation [On/Off].

WORK SUPPORT

Support ItemSettingDescription
VOLUME SETTING Vol. 1 Allows you to set volume of warning tone.
Low
Vol. 3
Middle
Vol. 5
High
Off

CONFIGURATION

Refer to Description.

CAN DIAG SUPPORT MNTR

Refer to CAN Diagnostic Support Monitor.