Engine

Engine Control System Symptoms

~5min read
Symptom Table

SYSTEM — BASIC ENGINE CONTROL SYSTEM

SYMPTOMReference page
HARD/NO START/RESTART (EXCP. HA)ENGINE STALLHESITATION/SURGING/FLAT SPOTSPARK KNOCK/DETONATIONLACK OF POWER/POOR ACCELERATIONHIGH IDLE/LOW IDLEROUGH IDLE/HUNTINGIDLING VIBRATIONSLOW/NO RETURN TO IDLEOVERHEATS/WATER TEMPERATURE HIGHEXCESSIVE FUEL CONSUMPTIONEXCESSIVE OIL CONSUMPTIONBATTERY DEAD (UNDER CHARGE)
Warranty symptom codeAAABACADAEAFAGAHAJAKALAMHA
Fuel Fuel pump circuit 1 1 2 3 2 2 2 3 2 Diagnosis Procedure
Fuel pressure regulator system 3 3 4 4 4 4 4 4 4 4 Work Procedure
Fuel injector circuit 1 1 2 3 2 2 2 2 Component Function Check
Evaporative emission system 3 3 4 4 4 4 4 4 4 4 System Description
Air Positive crankcase ventilation system 3 3 4 4 4 4 4 4 4 4 1 Positive Crankcase Ventilation (PCV)
Incorrect idle speed adjustment 1 1 1 1 1 Work Procedure
Electric throttle control actuator 1 1 2 3 3 2 2 2 2 2 2 DTC Description, DTC Description
Ignition Incorrect ignition timing adjustment 3 3 1 1 1 1 1 1 Work Procedure
Ignition circuit 1 1 2 2 2 2 2 2 Component Function Check
Power supply and ground circuit 2 2 3 3 3 3 3 2 3 Diagnosis Procedure
Mass air flow sensor circuit 1 1 2 2 2 2 2 2 DTC Description, DTC Description
Engine coolant temperature sensor circuit 3 3 3 DTC Description, DTC Description
Air fuel ratio (A/F) sensor 1 circuit DTC Description, DTC Description, DTC Description, DTC Description, DTC Description
Throttle position sensor circuit 2 2 DTC Description, DTC Description, DTC Description, DTC Description, DTC Description
Accelerator pedal position sensor circuit 3 2 1 DTC Description, DTC Description, DTC Description, DTC Description
Knock sensor circuit 2 3 DTC Description
Engine oil temperature sensor 4 2 3 DTC Description, DTC Description
Crankshaft position sensor (POS) circuit 2 2 DTC Description
Camshaft position sensor (PHASE) circuit 3 2 DTC Description
Nissan Murano Vehicle speed signal circuit 2 3 3 3 DTC Description
ECM 2 2 3 3 3 3 3 3 3 3 3 DTC Description, DTC Description
Intake valve timing control solenoid valve circuit 3 2 1 3 2 2 3 3 DTC Description
Intake valve timing intermediate lock control solenoid valve circuit DTC Description
Exhaust valve timing control solenoid valve 3 2 1 3 2 2 3 3 DTC Description
PNP signal circuit 3 3 3 3 3 DTC Description
VIAS control solenoid valve 1 circuit 1 DTC Description
VIAS control solenoid valve 2 circuit 1 DTC Description
Refrigerant pressure sensor circuit 2 3 3 4 Component Function Check
Electrical load signal circuit 3 Component Function Check
Air conditioner circuit 2 2 3 3 3 3 3 3 3 3 2 Work Flow
ABS actuator and electric unit (control unit) 4 Work Flow

1 - 6: The numbers refer to the order of inspection.

(continued on next page)

SYMPTOMReference page
HARD/NO START/RESTART (EXCP. HA)ENGINE STALLHESITATION/SURGING/FLAT SPOTSPARK KNOCK/DETONATIONLACK OF POWER/POOR ACCELERATIONHIGH IDLE/LOW IDLEROUGH IDLE/HUNTINGIDLING VIBRATIONSLOW/NO RETURN TO IDLEOVERHEATS/WATER TEMPERATURE HIGHEXCESSIVE FUEL CONSUMPTIONEXCESSIVE OIL CONSUMPTIONBATTERY DEAD (UNDER CHARGE)
Warranty symptom codeAAABACADAEAFAGAHAJAKALAMHA
Fuel Fuel tank 5 5 Inspection
Fuel piping 5 5 5 5 5 5
Vapor lock —
Valve deposit 5 5 5 5 5 5 5 —
Poor fuel (Heavy weight gasoline, Low octane) —
Air Air duct 5 5 5 5 5 5 Removal and Installation
Air cleaner Removal and Installation

Air leakage from air duct

(Mass air flow sensor — electric throttle control actuator)
5 5 5 5 Removal and Installation
Electric throttle control actuator Removal and Installation
Air leakage from intake manifold/Collector/Gasket Removal and Installation, Removal and Installation
Cranking Battery 1 1 1 1 1 1 1 1 Work Flow
Generator circuit Work Flow (With 165-DSS-5000P) (With 165-DSS-5000P)*, Work Flow (Without 165-DSS-5000P) (Without 165-DSS-5000P)*
Starter circuit 3 Work Flow (With 165-DSS-5000P) (With 165-DSS-5000P)*, Work Flow (Without 165-DSS-5000P) (Without 165-DSS-5000P)*
Signal plate 6 Inspection
PNP signal 4 DTC Description
Engine Cylinder head 5 5 5 5 5 5 5 5 Inspection After Disassembly
Cylinder head gasket 4 3
Cylinder block 6 6 6 6 6 6 6 6 4 Inspection
Piston
Piston ring
Connecting rod
Bearing
Crankshaft
Valve mechanism Timing chain 5 5 5 5 5 5 5 5 Removal and Installation
Camshaft Inspection after Installation
Intake valve timing control Removal and Installation
Exhaust valve timing control Removal and Installation
Intake valve 3 Inspection After Disassembly
Exhaust valve
Exhaust Exhaust manifold/Tube/Muffler/Gasket 5 5 5 5 5 5 5 5 Removal and Installation (bank 2), Removal and Installation (bank 2), Checking Exhaust System
Three way catalyst
Lubrication Oil pan/Oil strainer/Oil pump/Oil filter/Oil gallery/Oil cooler 5 5 5 5 5 5 5 5 Removal and Installation (Lower Oil Pan), Removal and Installation (Upper Oil Pan), Disassembly and Assembly, Removal and Installation, Engine Lubrication System
Oil level (Low)/Filthy oil Inspection
Cooling Radiator/Hose/Radiator filler cap 5 5 5 5 5 5 5 4 5 Removal and Installation, System Inspection
Thermostat 5 Removal and Installation
Water pump Removal and Installation
Water gallery Cooling Circuit
Cooling fan 5 Removal and Installation
Coolant level (Low)/Contaminated coolant System Inspection
NVIS (NISSAN Nissan Murano Vehicle Immobilizer System — NATS) 1 1 Work Flow

1 - 6: The numbers refer to the order of inspection.

*: For the details of the EXP-800 NI or GR8-1200 NI, refer to Special Service Tool.