Body Interior

Front Seat

~13min read
0204060801004936N·mlb·ft
Tightening torque found on this page
Exploded View

DRIVER SEAT WITH CLIMATE CONTROL

1. Headrest 2. Seat cushion trim 3. Seat cushion pad
4. Seatback assembly 5. Seat cushion outer finisher (RH) 6. Seat belt buckle
7. Seat cushion inner finisher [RH (front)] 8. Seat cushion inner finisher [RH (rear)] 9. Slide finisher outer (RH)
10. Front slide finisher (RH) 11. Seat frame assembly 12. Front slide finisher (LH)
13. Seat cushion blower 14. Blower motor bracket 15. Blower motor nozzle
16. Slide finisher outer (LH) 17. Power seat switch 18. Seat slide knob
19. Seat recline knob 20. Lumbar support switch 21. Seat cushion outer finisher (LH)
22. Driver seat control unit 23. Seat cushion inner finisher [LH (rear)] 24. Seat cushion inner finisher [LH (front)]
25. Rear slide finisher 26. Seat back blower 27. Seat harness
28. Headrest holder (locked) 29. Headrest holder (free) 30. Climate controlled seat control unit
A. Refer to Removal and Installation.

DRIVER SEAT WITHOUT CLIMATE CONTROL

1. Headrest 2. Seatback assembly 3. Seat cushion trim
4. Seat cushion pad 5. Seat cushion outer finisher (RH) 6. Seat belt buckle
7. Seat cushion inner finisher [RH (front)] 8. Seat cushion inner finisher [RH (rear)] 9. Slide finisher outer (RH)
10. Front seat heater (if equipped) 11. Front slide finisher (RH) 12. Seat frame assembly
13. Front slide finisher (LH) 14. Seat slide knob 15. Seat recline knob
16. Lumbar support switch 17. Seat cushion outer finisher (LH) 18. Power seat switch
19. Slide finisher outer (LH) 20. Driver seat control unit 21. Seat cushion inner finisher [LH (rear)]
22. Seat cushion inner finisher [LH (front)] 23. Rear slide finisher 24. Rear hinge cover
25. Seatback board 26. Seat harness 27. Headrest holder (locked)
28. Headrest holder (free) A. Rear hinge cover clips B. Seatback board clips
C. Refer to Removal and Installation.

DRIVER SEAT - MANUAL

1. Headrest 2. Headrest holder (free) 3. Seat cushion trim
4. Seat cushion pad 5. Seat cushion outer finisher (RH) 6. Seat belt buckle
7. Seat cushion inner finisher [RH (front)] 8. Seat cushion inner finisher [RH (rear)] 9. Slide finisher outer (RH)
10. Front slide finisher (RH) 11. Seat frame assembly 12. Front slide finisher (LH)
13. Front seat heater (if equipped) 14. Lift lever 15. Recline lever finisher
16. Seat cushion outer finisher (LH) 17. Slide finisher outer (LH) 18. Seat cushion inner finisher [LH (rear)]
19. Seat cushion inner finisher [LH (front)] 20. Rear slide finisher 21. Rear hinge cover
22. Seatback assembly 23. Seatback board 24. Seat harness
25. Headrest holder (locked) A. Rear hinge cover clips B. Seatback board clips
C. Refer to Removal and Installation.

PASSENGER SEAT WITH CLIMATE CONTROL

1. Headrest 2. Seat cushion trim 3. Seat cushion pad
4. Rear slide finisher 5. Seat cushion inner finisher [RH (front)] 6. Seat cushion outer finisher (RH)
7. Seat recline knob 8. Seat slide knob 9. Power seat switch
10. Seat cushion inner finisher [RH (rear)] 11. Slide finisher outer (RH) 12. Front slide finisher (RH)
13. Occupant Classification System control unit 14. Front slide finisher (LH) 15. Seat cushion blower
16. Blower motor bracket 17. Blower motor nozzle 18. Seat frame assembly
19. Occupant Classification System sensor 20. Occupant Classification System harness 21. Slide finisher outer (LH)
22. Seat cushion outer finisher (LH) 23. Seat belt buckle 24. Seat cushion inner finisher [LH (rear)]
25. Seat cushion inner finisher [LH (front)] 26. Seat back blower 27. Seat harness
28. Climate controlled seat control unit 29. Seatback assembly 30. Headrest holder (locked)
31. Headrest holder (free) A. Refer to Removal and Installation.

PASSENGER SEAT WITHOUT CLIMATE CONTROL

1. Seat harness 2. Headrest 3. Seat cushion trim
4. Seat cushion pad 5. Seat cushion inner finisher [RH (front)] 6. Seat cushion outer finisher (RH)
7. Seat recline knob 8. Seat slide knob 9. Power seat switch
10. Seat cushion inner finisher [RH (rear)] 11. Slide finisher outer (RH) 12. Front seat heater (if equipped)
13. Front slide finisher (RH) 14. Occupant Classification System control unit 15. Front slide finisher (LH)
16. Seat frame assembly 17. Occupant Classification System sensor 18. Occupant Classification System harness
19. Slide finisher outer (LH) 20. Seat cushion outer finisher (LH) 21. Seat belt buckle
22. Seat cushion inner finisher [LH (rear)] 23. Seat cushion inner finisher [LH (front)] 24. Rear slide finisher
25. Seat hinge cover 26. Seatback assembly 27. Seatback board
28. Headrest holder (locked) 29. Headrest holder (free) A. Rear hinge cover clips
B. Seatback board clips C. Refer to Removal and Installation.

PASSENGER SEAT - MANUAL

1. Headrest 2. Seat cushion trim 3. Seat cushion pad
4. Seat cushion inner finisher [RH (rear)] 5. Seat cushion inner finisher [RH (front)] 6. Seat cushion outer finisher (RH)
7. Front slide finisher (RH) 8. Slide finisher outer (RH) 9. Front slide finisher (RH)
10. Front seat heater (if equipped) 11. Occupant Classification System control unit 12. Front slide finisher (LH)
13. Occupant Classification System harness 14. Seat frame assembly 15. Occupant Classification System sensor
16. Slide finisher outer (LH) 17. Seat cushion outer finisher (LH) 18. Seat belt buckle
19. Seat cushion inner finisher [LH (rear)] 20. Seat cushion inner finisher [LH (front)] 21. Rear slide finisher
22. Seat harness 23. Seat hinge cover 24. Seatback assembly
25. Headrest holder (locked) 26. Headrest holder (free) 27. Seatback board
A. Rear hinge cover clips B. Seatback board clips C. Refer to Removal and Installation.
Removal and Installation

REMOVAL

Slide seat to full rearward position.

Disconnect negative and positive battery terminals then wait at least three minutes. Refer to Removal and Installation.

Disconnect harness connector for side air bag module.

Release pawls using a suitable tool and remove front finishers (LH/RH) (A) then remove seat front bolts.

Connect negative and positive battery terminals then slide seat to full forward position. Refer to Removal and Installation (power seat only).

Disconnect negative and positive battery terminals then wait at least three minutes. Refer to Removal and Installation (power seat only).

Remove rear slide finishers (LH/RH) (B) by lifting up and then pulling rearward, then remove seat rear bolts.

Tilt seat rearward and disconnect harness connectors from seat.

Remove seat from the Nissan Murano vehicle.

INSTALLATION

Installation is in the reverse order of removal.

LH front seat bolt torque : 49 N·m

  • When installing front seat (RH), tighten bolts in the order shown.

  • Tighten seat bolts to specification.

RH front seat bolt torque : 49 N·m

Seatback Board

REMOVAL

Disconnect negative and positive battery terminals then wait at least three minutes. Refer to Removal and Installation.

Release seatback board lower clips (C).

Reach behind seatback board and press center clips (B) inward and release from seatback frame.

Pull seatback board down releasing upper clips (A) and remove.

INSTALLATION

Installation is in the reverse order of removal.

Seat Hinge Cover

REMOVAL

Remove seatback board. Refer to Seatback Board.

Release seatback trim J-hooks.

: J-hook

Release two J-hook retainers (A) from seat frame assembly.

Release seat hinge cover clips (B) then remove seat hinge cover (1).

INSTALLATION

Installation is in the reverse order of removal.

Seat Cushion Blower

REMOVAL

Remove front seat. Refer to Removal and Installation.

Release seatback J-hook (A) and position seatback flap (B) aside.

Disconnect harness connector (A) and remove screws (B) from the seat cushion blower.

Release clips and remove seat cushion blower (1).

: Clip

INSTALLATION

Installation is in the reverse order of removal.

Seat Back Blower

REMOVAL

Remove front seat. Refer to Removal and Installation.

Release seatback J-hook (A) and position seatback flap (B) aside.

Release seatback zippers (A), and release J-clip retainer (B), then position upper seatback trim aside.

Release J-hooks (A) and position lower seatback trim aside.

Disconnect harness connector (A) and remove screws (B) from seat back blower.

Release clips and remove seat back blower (1).

: Clip

INSTALLATION

Installation is in the reverse order of removal.

Climate Controlled Seat Switch

REMOVAL

Release clips and pawls using a suitable tool and remove center console side finisher (LH/RH).

Release clips and remove center console upper side finisher (LH/RH).

Release clips and screws and remove center console lower side finisher (LH/RH).

Remove cluster lid C. Refer to Removal and Installation.

Remove shift selector knob. Refer to Exploded View.

Release clips using a suitable tool then disconnect harness connectors and remove shift selector finisher. Refer to Exploded View.

Release pawls using a suitable tool and remove climate controlled seat switch (1, 2).

:Pawl

INSTALLATION

Installation is in the reverse order of removal.

Climate Controlled Seat Control Unit

REMOVAL

Remove front seat. Refer to Removal and Installation.

Release seatback J-hook (A) and position seatback flap (B) aside.

Remove screws (A) and disconnect harness connectors (B), then remove climate controlled seat control unit (1).

INSTALLATION

Installation is in the reverse order of removal.

Front Heated Seat Switch

REMOVAL

Release clips and pawls using a suitable tool and remove center console side finisher (LH/RH).

Release clips and remove center console upper side finisher (LH/RH).

Release clips and screws and remove center console lower side finisher (LH/RH).

Remove cluster lid C. Refer to Removal and Installation.

Remove shift selector knob. Refer to Exploded View.

Release clips using a suitable tool then disconnect harness connectors and remove shift selector finisher. Refer to Exploded View.

Release pawls using a suitable tool and remove heated seat switch (1, 2).

:Pawl

INSTALLATION

Installation is in the reverse order of removal.

Front Seat Heater

REMOVAL

Remove seat cushion pad. Refer to Seat Cushion (LH), or Seat Cushion (RH).

Carefully remove front seat heater from seat cushion pad.

INSTALLATION

Peel protective backing from front seat heater and attach to seat cushion pad.

Secure front seat heater harness to seat cushion frame.

Install remaining seat cushion components. Refer to Seat Cushion (LH), or Seat Cushion (RH).

Power Seat Switch

EXPLODED VIEW

1. Seat cushion outer finisher 2. Power seat switch

REMOVAL

Remove seat cushion outer finisher (1).

Remove screw (A). Release metal clip (B) from seat frame assembly (2), as shown.

: Metal clip

Release pawls and metal clip (C), and remove.

: Pawl

: Metal clip

Disconnect harness connectors from power seat switch and lumbar support switch (if equipped).

Disconnect harness connector from power seat switch.

Remove screws and power seat switch.

INSTALLATION

Installation is in the reverse order of removal.

Lumbar Support Switch

EXPLODED VIEW

1. Seat cushion outer finisher 2. Lumbar support switch Pawl

REMOVAL

Remove seat cushion outer finisher (1).

Remove screw (A). Release metal clip (B) from seat frame assembly (2), as shown.

: Metal clip

Release pawls and metal clip (C), and remove.

: Pawl

: Metal clip

Disconnect harness connector from lumbar support switch.

Using a suitable tool release pawls and remove lumbar support switch.

INSTALLATION

Installation is in the reverse order of removal.