Electrical & Power Control

System. Power Distribution System

~4min read
System Description

SYSTEM DIAGRAM

Signal transmission function list

Signal nameInputOutputDescription
Push-button ignition switch signal Push-button ignition switch BCM Transmits the push-button ignition switch signal to the BCM.
ACC/ON indicator lamp signal BCM Push-button ignition switch Activates/deactivates push-button ignition switch illumination using the ACC/ON indicator lamp signal.
Stop lamp switch signal Stop lamp switch BCM Transmits the stop lamp switch signal to the BCM.
Detent switch signal CVT shift selector (detent switch) BCM Transmits the detent switch signal to the BCM.
P/N position signal Transmission range switch BCM Transmits the P/N position signal to the BCM.
Ignition relay-1 control signal BCM IPDM E/R Transmits the ignition relay-1 control signal to the IPDM E/R.
Push-button ignition switch ON signal BCM IPDM E/R (CAN) Transmits the push-button ignition switch ON signal via CAN communication.
Push-button ignition switch status signal IPDM E/R BCM (CAN) Transmits the push-button ignition switch status signal via CAN communication.

SYSTEM DESCRIPTION

  • PDS (POWER DISTRIBUTION SYSTEM) is the system that BCM controls with the operation of the push-button ignition switch and performs the power distribution to each power circuit. This system is used instead of the mechanical power supply changing mechanism with the operation of the conventional key cylinder.

  • The push-button ignition switch can be operated when Intelligent Key is in the following condition:

    • Intelligent Key is in the detection area of the inside key antenna.

    • Intelligent Key backside is contacted to push-button ignition switch.

  • The push-button ignition switch operation is input to BCM as a signal. BCM changes the power supply position according to the status of the push-button ignition switch and operates the following relays to supply power to each power circuit:

    • Ignition relay-1 (IPDM E/R)

    • Ignition relay-2 [Fuse block (J/B)]

    • Accessory relay-1 [Fuse block (J/B)]

    • Front blower motor relay [Fuse block (J/B)]

  • The power supply position can be confirmed with the lighting of the indicators in the push-button ignition switch.

IGNITION BATTERY SAVER SYSTEM

When all the following conditions are met for a period of time, the battery saver system will turn off the power supply (push-button ignition switch ON/ACC → OFF) to prevent battery discharge:

  • Push-button ignition switch is in ACC or ON

  • Turn signal lamp is not in operation

  • Selector lever is in the P (park) position

Reset Condition of Ignition Battery Saver System

If any of the following conditions are met, the battery saver system is released:

  • Push-button ignition switch is not in ACC or ON

  • Turn signal lamp is in operation

  • Selector lever is not in the P (park) position

POWER SUPPLY POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION

The power supply position changing operation can be performed with the following operations:

Vehicle speed: less than 4 km/h

Power supply positionEngine start/stop conditionPush-button ignition switch operation frequency
Selector lever positionBrake pedal operation condition
OFF → ACC — Not depressed 1
OFF → ACC → ON — Not depressed 2
OFF → ACC → ON → OFF — Not depressed 3

OFF → START

ACC → START

ON → START
P or N position Depressed 1
Engine is running → OFF — — 1

Vehicle speed: 4 km/h or more

Power supply positionEngine start/stop conditionPush-button ignition switch operation frequency
Selector lever positionBrake pedal operation condition
Engine is running → ACC — — Emergency stop operation
Engine stall return operation while driving N position Not depressed 1

Emergency stop operation

  • Press and hold the push-button ignition switch for 2 seconds or more.

  • Press the push-button ignition switch 3 times or more within 1.5 seconds.