Engine Coolant Pump No Signal (P26CA31)
DESCRIPTION
Refer to DTC P26CA12.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
P26CA31 |
Engine Coolant Pump No Signal |
The speed of the engine water pump calculated from the WPI signal is less than 10 rpm (open or short in the WPI circuit) (1 trip detection logic). |
|
Comes on |
|
DTC No. | Data List |
|---|---|
P26CA31 |
|
MONITOR DESCRIPTION
The ECM receives a frequency signal (WPI) from the inverter water pump with motor assembly and calculates the speed of the inverter water pump with motor assembly. As the frequency signal (WPI) is 4 Hz when the inverter water pump with motor assembly is stopped to enable the ECM to detect an open or short in the signal line, the inverter water pump with motor assembly speed will be displayed as approximately 160 rpm even when the pump is stopped. If the inverter water pump with motor assembly speed is calculated to be less than 10 rpm, the ECM judges that there is an open or short in the WPI circuit and stores this DTC.
MONITOR STRATEGY
Related DTCs |
P26CA: Engine water pump circuit verify pulse input |
Required Sensors/Components (Main) |
Water inlet housing with water pump sub-assembly |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
15 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Auxiliary battery voltage |
8 V or higher |
Ignition switch |
ON |
Time after ignition switch off to ON |
0.5 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
Engine water pump speed |
Less than 10 rpm |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
.gif)
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
.gif)
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON.
- Turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON [A].
- Turn the GTS on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here
.gif)
- Start the engine and maintain the engine speed at 2500 rpm or more for at least 40 seconds [B].
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P26CA31.
- Check the DTC judgment result.
GTS Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
- [A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P26CA12.
Click here ![]()
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click here
.gif)
(Select Powertrain in Health Check and then check the time stamp data.)
- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here
.gif)
HINT:
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK TERMINAL VOLTAGE (POWER SOURCE OF INVERTER WATER PUMP WITH MOTOR ASSEMBLY)
*a |
Front view of wire harness connector (to Inverter Water Pump with Motor Assembly) |
(a) Disconnect the inverter water pump with motor assembly connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C131-2 (NWP) - Body ground |
Ignition switch ON |
11 to 14 V |
| NG | GO TO STEP 8 |
|
CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP WITH MOTOR ASSEMBLY - BODY GROUND)
(a) Disconnect the inverter water pump with motor assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C131-1 (PGND) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF INVERTER WATER PUMP WITH MOTOR ASSEMBLY)
*a |
Front view of wire harness connector (to Inverter Water Pump with Motor Assembly) |
(a) Disconnect the inverter water pump with motor assembly connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C131-4 (+B) - Body ground |
Ignition switch ON |
11 to 14 V |
| OK | REPLACE INVERTER WATER PUMP WITH MOTOR ASSEMBLY |
|
INSPECT EFI-MAIN NO. 3 RELAY
Click here ![]()
| NG | REPLACE EFI-MAIN NO. 3 RELAY |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI-MAIN NO. 3 RELAY)
(a) Remove the EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
3 (EFI-MAIN NO. 3 relay) - Body ground |
Always |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - EFI-MAIN NO. 3 RELAY) |
|
CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 3 RELAY - BODY GROUND)
(a) Remove the EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
1 (EFI-MAIN NO. 3 relay) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 3 RELAY - INVERTER WATER PUMP WITH MOTOR ASSEMBLY)
(a) Remove the EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.
(b) Disconnect the inverter water pump with motor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
5 (EFI-MAIN NO. 3 relay) - C131-4 (+B) |
Always |
Below 1 Ω |
5 (EFI-MAIN NO. 3 relay) or C131-4 (+B) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK | REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 3 RELAY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP WITH MOTOR ASSEMBLY - ECM)
(a) Disconnect the inverter water pump with motor assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C131-2 (NWP) - C139-51 (WPI) |
Always |
Below 1 Ω |
C131-2 (NWP) or C139-51 (WPI) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |