Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
INSPECT SPIRAL CABLE SUB-ASSEMBLY |
84306 |
- |
- |
|
2 |
STEERING SENSOR |
89245B |
- |
- |
|
3 |
PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
- |
- |
- |
|
4 |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
- |
- |
- |
|
5 |
UPPER STEERING COLUMN COVER |
45286B |
- |
- |
- |
6 |
LOWER STEERING COLUMN COVER |
45287 |
- |
- |
- |
7 |
ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
84306 |
- |
- |
|
*1 |
SPIRAL CABLE SUB-ASSEMBLY |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
8 |
STEERING WHEEL ASSEMBLY |
45100 |
- |
- |
|
9 |
HORN BUTTON ASSEMBLY |
45130 |
- |
- |
|
10 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
11 |
UPDATE ECU SECURITY KEY |
- |
- |
- |
|
12 |
INSPECT SRS WARNING LIGHT |
- |
- |
- |
|
13 |
INSPECT HORN BUTTON ASSEMBLY |
45130 |
- |
- |
|
14 |
CHECK STEERING WHEEL CENTER POINT |
- |
- |
- |
|
15 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
- |
- |
NOTICE:
- After replacing the steering sensor, make sure to perform update ECU security key.
- After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
- A lock pin is installed to a new steering sensor. Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.
PROCEDURE
1. INSPECT SPIRAL CABLE SUB-ASSEMBLY
Click here ![]()
2. INSTALL STEERING SENSOR
*a |
Guide |
*b |
Pin |
*c |
Lock Pin |
- |
- |
(1) Align the 2 pins and 2 guides, and engage the 6 claws to install the steering sensor to the spiral cable sub-assembly.
NOTICE:
- Do not remove the lock pin before the steering sensor is installed to the spiral cable sub-assembly.
- Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.
- The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the steering sensor to the spiral cable sub-assembly.
(2) Remove the lock pin from the steering sensor.
3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
Click here ![]()
4. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
![]() |
Click here |
5. INSTALL UPPER STEERING COLUMN COVER
6. INSTALL LOWER STEERING COLUMN COVER
7. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Click here ![]()
8. INSTALL STEERING WHEEL ASSEMBLY
![]() |
Click here |
9. INSTALL HORN BUTTON ASSEMBLY
![]() |
Click here |
10. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
- for M20A-FKS:
Click here
.gif)
- for M20A-FXS:
Click here
.gif)
11. UPDATE ECU SECURITY KEY
Click here ![]()
HINT:
When the steering sensor is replaced with a new one, ECU security key is necessary.
12. INSPECT SRS WARNING LIGHT
Click here ![]()
13. INSPECT HORN BUTTON ASSEMBLY
Click here ![]()
14. CHECK STEERING WHEEL CENTER POINT
Click here ![]()
15. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
.png)
.png)
.png)
.png)