Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
BRAKE BOOSTER GASKET |
44785 |
- |
- |
- |
2 |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY |
47210L |
- |
- |
|
3 |
PUSH ROD PIN |
47264A |
- |
- |
|
4 |
BRAKE PEDAL RETURN SPRING |
47101A |
- |
- |
|
5 |
CONNECT BRAKE LINE |
- |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
* |
For use with a union nut wrench |
● |
Non-reusable part |
![]() |
Lithium soap base glycol grease |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
55606 |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
7 |
FRONT NO. 5 BRAKE TUBE |
47315 |
- |
- |
|
8 |
NO. 4 BRAKE TUBE CLAMP |
47374B |
- |
- |
|
9 |
NO. 3 BRAKE TUBE CLAMP |
47373B |
- |
- |
|
10 |
ENGINE ROOM MAIN WIRE |
82111 |
- |
- |
|
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
* |
For use with a union nut wrench |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
11 |
BLEED BRAKE LINE |
- |
- |
- |
- |
12 |
OUTER COWL TOP PANEL SUB-ASSEMBLY |
55701J |
- |
- |
- |
13 |
WATER GUARD PLATE |
55734D |
- |
- |
- |
14 |
NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL |
55737B |
- |
- |
- |
15 |
WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
- |
- |
- |
- |
16 |
FRONT WHEEL LH |
- |
- |
- |
- |
17 |
CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
18 |
UPDATE ECU SECURITY KEY |
- |
- |
- |
|
19 |
INSPECT AND ADJUST BRAKE PEDAL |
- |
- |
- |
- |
20 |
PERFORM BRAKE SYSTEM CALIBRATION |
- |
- |
- |
- |
21 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
![]() |
For use with a union nut wrench |
NOTICE:
- After replacing the brake booster with master cylinder assembly, make sure to perform update ECU security key.
- After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
PROCEDURE
1. INSTALL BRAKE BOOSTER GASKET
2. INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
(1) Install the brake booster with master cylinder assembly with the 4 nuts.
Torque:
12,7 N·m {130 kgf·cm, 9 ft·lbf}
NOTICE:
- Tighten the nuts in the order shown in the illustration.
- Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.*a
Connectors
*b
Boot
*c
Brake Master Cylinder Push Rod Clevis
*d
Brake Master Cylinder Reservoir Assembly
- Be careful not to allow brake fluid to enter the connector.
- If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.
3. INSTALL PUSH ROD PIN
![]() |
Click here |
4. INSTALL BRAKE PEDAL RETURN SPRING
![]() |
Click here |
5. CONNECT BRAKE LINE
*a |
Torque Wrench Fulcrum Length |
- |
- |
(1) Using a union nut wrench, connect the 2 brake lines to the brake booster with master cylinder assembly.
Torque:
Specified tightening torque :
19,5 N·m {199 kgf·cm, 14 ft·lbf}
NOTICE:
- Do not kink or damage the brake lines.
- Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
- Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
7. CONNECT FRONT NO. 5 BRAKE TUBE
*a |
Torque Wrench Fulcrum Length |
- |
- |
![]() |
Connect in this direction |
- |
- |
(1) Using a union nut wrench, connect the front No. 5 brake tube to the brake actuator assembly.
Torque:
Specified tightening torque :
15,2 N·m {155 kgf·cm, 11 ft·lbf}
NOTICE:
- Do not kink or damage the brake lines.
- Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
(2) Connect the front brake tube grommet to the vehicle body.
(3) Using a union nut wrench, connect the front No. 5 brake tube to the front flexible hose LH.
Torque:
Specified tightening torque :
15,2 N·m {155 kgf·cm, 11 ft·lbf}
NOTICE:
- Do not kink or damage the brake lines.
- Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
8. INSTALL NO. 4 BRAKE TUBE CLAMP
![]() |
NOTICE:
|
9. INSTALL NO. 3 BRAKE TUBE CLAMP
![]() |
NOTICE:
|
10. CONNECT ENGINE ROOM MAIN WIRE
![]() |
Connect the connector |
![]() |
Lock the lock lever |
(1) Connect the connector to the brake booster as shown in the illustration.
NOTICE:
- Make sure that the connector is locked securely.
- Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.
![]() |
Connect the connector in this direction |
![]() |
Connect the connector in this direction |
(1) Connect the connector (B) to the brake master cylinder reservoir assembly as shown in the illustration
(2) Engage the clamp to the brake master cylinder reservoir assembly.
(3) Connect the connector (A) to the brake booster.
11. BLEED BRAKE LINE
Click here ![]()
12. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Click here ![]()
13. INSTALL WATER GUARD PLATE
14. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
15. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here ![]()
16. INSTALL FRONT WHEEL LH
Click here ![]()
17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
18. UPDATE ECU SECURITY KEY
HINT:
Perform this procedure only when replacement of the brake booster with master cylinder assembly is necessary.
Click here ![]()
19. INSPECT AND ADJUST BRAKE PEDAL
Click here ![]()
20. PERFORM BRAKE SYSTEM CALIBRATION
Click here ![]()
21. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
.png)
.png)
.png)
.png)
.png)
.png)
.png)
.png)