Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 2 TRANSMISSION CONTROL ECU BRACKET |
89539N |
- |
- |
- |
2 |
NO. 1 TRANSMISSION CONTROL ECU BRACKET |
89539M |
- |
- |
- |
3 |
TCM |
89535B |
- |
- |
|
4 |
ENGINE WIRE |
82121 |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
* |
For use with a union nut wrench |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
REAR ENGINE UNDER COVER LH |
51444A |
- |
- |
- |
6 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
7 |
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
8 |
UPDATE ECU SECURITY KEY |
- |
- |
- |
|
9 |
RESET MEMORY |
- |
- |
- |
|
10 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
NOTICE:
- After replacing the TCM, make sure to perform update ECU security key.
- After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.
PROCEDURE
1. INSTALL NO. 2 TRANSMISSION CONTROL ECU BRACKET
Torque:
5,8 N·m {59 kgf·cm, 51 in·lbf}
2. INSTALL NO. 1 TRANSMISSION CONTROL ECU BRACKET
Torque:
5,8 N·m {59 kgf·cm, 51 in·lbf}
3. INSTALL TCM
(1) Install the TCM to the continuously variable transaxle assembly with the 2 bolts.
Torque:
12,5 N·m {127 kgf·cm, 9 ft·lbf}
(2) Connect the connector and rotate the lever and engage the claw.
NOTICE:
Rotate the lever until the claw of the connector makes a click sound.
4. INSTALL ENGINE WIRE
*a |
Torque Wrench Fulcrum Length |
- |
- |
(1) Using a 10 mm union nut wrench, install the engine wire to the No. 2 transmission control ECU bracket with the bolt.
Torque:
Specified Tightening Torque :
10 N·m {102 kgf·cm, 7 ft·lbf}
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162mm (6.38 in.)): 8.8 N*m (90 kgf*cm, 78 in.*lbf)
5. INSTALL REAR ENGINE UNDER COVER LH
6. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
7. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
8. UPDATE ECU SECURITY KEY
Click here ![]()
9. RESET MEMORY
NOTICE:
If continuously variable transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.
Click here ![]()
10. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
.png)
.png)
.png)
.png)