Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR ENGINE OIL SEAL |
11401L |
- |
- |
|
2 |
NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
19315 |
- |
- |
|
3 |
DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
32101B |
- |
- |
|
4 |
CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY |
30400 |
- |
- |
- |
*1 |
REAR DRIVE PLATE SPACER |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
MP grease |
![]() |
Adhesive 1324 |
★ |
Precoated part |
- |
- |
NOTICE:
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![]()
PROCEDURE
1. INSTALL REAR ENGINE OIL SEAL
*a |
-0.9 to 1.1 mm |
- |
- |
(1) Apply MP grease to the lip of a new rear engine oil seal.
NOTICE:
- Keep the lip free from foreign matter.
- Do not allow MP grease to contact the dust seal.
(2) Using SST and a hammer, tap in the rear engine oil seal.
SST: 09223-15030
SST: 09950-70010
09951-07150
Standard Depth:
-0.9 to 1.1 mm (-0.0354 to 0.0433 in.) (From the edge of the cylinder block sub-assembly and stiffening crankcase assembly)
NOTICE:
Do not tap in the rear engine oil seal at an angle.
2. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
(1) Install the No. 1 crankshaft position sensor plate.
HINT:
Align the pin hole of the No. 1 crankshaft position sensor plate with the pin of the crankshaft.
3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
*1 |
Drive Plate and Ring Gear Sub-assembly |
*2 |
Rear Drive Plate Spacer |
*3 |
No. 1 Crankshaft Position Sensor Plate |
- |
- |
![]() |
Transaxle Side |
- |
- |
(1) Using SST, hold the crankshaft pulley assembly.
SST: 09213-54015
SST: 09330-00021
(2) Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.
NOTICE:
As the rear drive plate spacer, drive plate and ring gear sub-assembly and No. 1 crankshaft position sensor plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.
(3) Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
(4) Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.
Torque:
150 N·m {1530 kgf·cm, 111 ft·lbf}
NOTICE:
Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.
4. INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
- for 2WD
Click here
.gif)
- for AWD
Click here
.gif)
.png)
.png)
.png)
.png)
.png)
.png)