Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR SPRING SEAT SUB-ASSEMBLY |
42011 |
- |
- |
- |
2 |
SEPARATE REAR SHOCK ABSORBER ASSEMBLY |
- |
- |
- |
|
3 |
REAR LOWER COIL SPRING INSULATOR |
48258C |
- |
- |
- |
4 |
REAR UPPER COIL SPRING INSULATOR |
48259A |
- |
- |
- |
5 |
REAR COIL SPRING |
48231B |
- |
- |
|
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
6 |
SKID CONTROL SENSOR WIRE LH |
89544E |
- |
- |
|
7 |
SKID CONTROL SENSOR WIRE RH |
89544D |
- |
- |
|
8 |
REAR BRAKE TUBE FLEXIBLE HOSE LH |
- |
- |
- |
|
9 |
REAR BRAKE TUBE FLEXIBLE HOSE RH |
- |
- |
- |
|
10 |
BLEED BRAKE LINE |
- |
- |
- |
|
11 |
REAR WHEELS |
- |
- |
- |
- |
12 |
STABILIZE SUSPENSION |
- |
- |
- |
|
13 |
REAR AXLE BEAM ASSEMBLY |
42110F |
- |
- |
|
14 |
INSTALL REAR SHOCK ABSORBER ASSEMBLY |
- |
- |
- |
|
15 |
CHECK FOR SPEED SENSOR SIGNAL |
- |
- |
- |
|
16 |
INSPECT REAR WHEEL ALIGNMENT |
- |
- |
- |
|
17 |
PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
- |
- |
- |
|
18 |
PERFORM CALIBRATION |
- |
- |
- |
|
*A |
w/ Parking Assist Monitor System |
- |
- |
*1 |
REAR NO. 4 BRAKE TUBE |
*2 |
REAR NO. 3 BRAKE TUBE |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
* |
For use with a union nut wrench |
● |
Non-reusable part |
HINT:
- Use the same procedure for the RH side and LH side.
- The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL REAR SPRING SEAT SUB-ASSEMBLY
![]() |
HINT: Perform this procedure only when replacement of the rear spring seat sub-assembly is necessary. |
Torque:
35 N·m {357 kgf·cm, 26 ft·lbf}
2. SEPARATE REAR SHOCK ABSORBER ASSEMBLY
![]() |
Click here |
3. INSTALL REAR LOWER COIL SPRING INSULATOR
4. INSTALL REAR UPPER COIL SPRING INSULATOR
5. INSTALL REAR COIL SPRING
*a |
Identification Mark |
*b |
30° |
![]() |
Rear of the Vehicle |
![]() |
Lower of the Vehicle |
(1) Set the rear coil spring to the rear axle beam assembly as shown in the illustration.
NOTICE:
Make sure that the identification mark is positioned on the lower side of the vehicle.
*a |
Wooden Block |
*b |
Jack |
(1) Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks and temporarily install the rear axle beam assembly and rear coil spring with the 2 bolts and 2 nuts.
NOTICE:
Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.
6. INSTALL SKID CONTROL SENSOR REAR LH
![]() |
NOTICE: Do not twist the skid control sensor wire when installing it. |
Torque:
8 N·m {82 kgf·cm, 71 in·lbf}
7. INSTALL SKID CONTROL SENSOR REAR RH
8. CONNECT REAR BRAKE TUBE FLEXIBLE HOSE LH
*a |
Torque Wrench Fulcrum Length |
- |
- |
(1) Temporarily install the rear brake tube flexible hose LH to the rear No. 4 brake tube.
(2) Secure the rear brake tube flexible hose LH with a new clip.
NOTICE:
Install the clip as far as it will go.
(3) Using a union nut wrench, connect the rear brake tube flexible hose LH to the rear No. 4 brake tube while holding the rear brake tube flexible hose with a wrench.
Torque:
Specified tightening torque :
15,2 N·m {155 kgf·cm, 11 ft·lbf}
NOTICE:
- Do not kink or damage the brake line.
- Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
9. CONNECT REAR BRAKE TUBE FLEXIBLE HOSE RH
10. BLEED BRAKE LINE
Click here
![]()
11. INSTALL REAR WHEELS
Click here ![]()
12. STABILIZE SUSPENSION
Click here ![]()
13. INSTALL REAR AXLE BEAM ASSEMBLY
*a |
70 mm (2.76 in.) |
- |
- |
(1) Install the rear axle beam assembly as shown in the illustration.
Torque:
140 N·m {1428 kgf·cm, 103 ft·lbf}
14. INSTALL REAR SHOCK ABSORBER ASSEMBLY
*A |
for LH Side |
*B |
for RH Side |
(1) Install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts.
Torque:
49 N·m {500 kgf·cm, 36 ft·lbf}
NOTICE:
Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.
15. CHECK FOR SPEED SENSOR SIGNAL
Click here
![]()
16. INSPECT REAR WHEEL ALIGNMENT
Click here ![]()
17. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
Click here
![]()
18. PERFORM CALIBRATION (w/ Parking Assist Monitor System)
Parking assist monitor system |
|
Automatic headlight beam level control system |
.png)
.png)
.png)
.png)
.png)
.png)
.png)