Rear Axle Hub Bolt (for Awd)
Components
COMPONENTS
ILLUSTRATION
*1 |
REAR AXLE HUB BOLT |
*2 |
REAR DISC BRAKE CALIPER ASSEMBLY |
*3 |
REAR DISC |
*4 |
NO. 2 PARKING BRAKE WIRE ASSEMBLY |
*5 |
REAR FLEXIBLE HOSE |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
Replacement
REPLACEMENT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR WHEEL
Click here ![]()
2. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
(a) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly. NOTICE:
|
![]() |
3. SEPARATE REAR FLEXIBLE HOSE
(a) Remove the bolt and separate the rear flexible hose from the No. 4 flexible hose bracket. |
![]() |
4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
(a) Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly. NOTICE: Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose. |
![]() |
5. REMOVE REAR DISC
Click here
![]()
6. REMOVE REAR AXLE HUB BOLT
(a) Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
*a |
Service Nut |
![]() |
Turn |
Recommended Service Nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
NOTICE:
Install the service nuts to prevent damage to the rear axle hub bolts.
(b) Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
SST: 09611-12010
NOTICE:
Do not damage the threads of the rear axle hub bolts.
7. INSTALL REAR AXLE HUB BOLT
(a) Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
(b) Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
*a |
Service Nut |
*b |
Washer |
![]() |
Turn |
Recommended Service Nut:
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
HINT:
Recommended washer thickness is 5 mm (0.197 in.) or more.
(c) Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
NOTICE:
- Install the service nuts to prevent damage to the rear axle hub bolts.
- Do not damage the threads of the rear axle hub bolts.
(d) Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
8. INSTALL REAR DISC
Click here
![]()
9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
(a) Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.
Torque:
107 N·m {1091 kgf·cm, 79 ft·lbf}
NOTICE:
- Do not twist the rear flexible hose when installing the rear disc brake caliper assembly.
- Make sure that there is no foreign matter on the threads of the bolt.
10. INSTALL REAR FLEXIBLE HOSE
(a) Install the rear flexible hose to the No. 4 flexible hose bracket with the bolt.
Torque:
29 N·m {296 kgf·cm, 21 ft·lbf}
11. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
(a) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.
NOTICE:
- Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
- Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
12. INSTALL REAR WHEEL
Click here ![]()
.png)



.png)