Reassembly
REASSEMBLY
COMPONENTS (REASSEMBLY)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
NO. 5 FRONT WHEEL OPENING EXTENSION PAD |
53855B |
- |
- |
|
2 |
NO. 3 FRONT WHEEL OPENING EXTENSION PAD |
53853 |
- |
- |
|
3 |
NO. 4 FRONT WHEEL OPENING EXTENSION PAD |
53854 |
- |
- |
|
*1 |
FRONT FENDER MOULDING |
- |
- |
● |
Non-reusable part |
- |
- |
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL NO. 5 FRONT WHEEL OPENING EXTENSION PAD
![]() |
NOTICE: When installing a new No. 5 front wheel opening extension pad, heat the front fender moulding using a heat light. |
Standard:
Item | Temperature |
|---|---|
Front Fender Moulding |
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the front fender moulding excessively.
*a |
Location Line |
- |
- |
(1) Clean the front fender moulding.
1. Using a heat light, heat the front fender moulding surface.
2. Remove any remaining double-sided tape from the front fender moulding.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 5 front wheel opening extension pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 5 front wheel opening extension pad.
1. Using a heat light, heat the front fender moulding.
2. Remove the release paper from the No. 5 front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 5 front wheel opening extension pad as shown in the illustration.
HINT:
- Make sure that the end of the No. 5 front wheel opening extension pad is between the location lines.
- Press the No. 5 front wheel opening extension pad firmly to install it.
2. INSTALL NO. 3 FRONT WHEEL OPENING EXTENSION PAD
![]() |
NOTICE: When installing a new No. 3 front wheel opening extension pad, heat the front fender moulding using a heat light. |
Standard:
Item | Temperature |
|---|---|
Front Fender Moulding |
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the front fender moulding excessively.
*a |
Location Line |
- |
- |
(1) Clean the front fender moulding.
1. Using a heat light, heat the front fender moulding surface.
2. Remove any remaining double-sided tape from the front fender moulding.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 3 front wheel opening extension pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 3 front wheel opening extension pad.
1. Using a heat light, heat the front fender moulding.
2. Remove the release paper from the No. 3 front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 3 front wheel opening extension pad as shown in the illustration.
HINT:
- Make sure that the end of the No. 3 front wheel opening extension pad is between the location lines.
- Press the No. 3 front wheel opening extension pad firmly to install it.
3. INSTALL NO. 4 FRONT WHEEL OPENING EXTENSION PAD
![]() |
NOTICE: When installing a new No. 4 front wheel opening extension pad, heat the front fender moulding using a heat light. |
Standard:
Item | Temperature |
|---|---|
Front Fender Moulding |
20 to 30 °C |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the front fender moulding excessively.
*a |
Location Line |
- |
- |
(1) Clean the front fender moulding.
1. Using a heat light, heat the front fender moulding surface.
2. Remove any remaining double-sided tape from the front fender moulding.
3. Wipe off any tape adhesive residue with cleaner.
NOTICE:
- Installing the No. 4 front wheel opening extension pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
(2) Install a new No. 4 front wheel opening extension pad.
1. Using a heat light, heat the front fender moulding.
2. Remove the release paper from the No. 4 front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
3. Install the No. 4 front wheel opening extension pad as shown in the illustration.
HINT:
- Make sure that the end of the No. 4 front wheel opening extension pad is between the location lines.
- Press the No. 4 front wheel opening extension pad firmly to install it.
.png)
.png)
.png)
.gif)