Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
PRECAUTION |
- |
- |
- |
|
2 |
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL |
- |
- |
- |
- |
3 |
DRAIN BRAKE FLUID |
- |
- |
- |
|
4 |
WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
- |
- |
- |
- |
5 |
NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL |
55737B |
- |
- |
- |
6 |
WATER GUARD PLATE |
55734D |
- |
- |
- |
7 |
OUTER COWL TOP PANEL SUB-ASSEMBLY |
55701J |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
8 |
NO. 1 ENGINE UNDER COVER ASSEMBLY |
51410 |
- |
- |
- |
9 |
DASH PANEL HEAT INSULATOR |
55225C |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
10 |
BRAKE LINE |
- |
- |
- |
|
11 |
BRAKE ACTUATOR WITH BRACKET |
- |
- |
- |
|
*1 |
CONNECTOR |
*2 |
No. 1 BRAKE TUBE CLAMP |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
12 |
BRAKE ACTUATOR ASSEMBLY |
44510 |
- |
- |
|
13 |
NO. 1 BRAKE ACTUATOR CASE COLLAR |
44521A |
- |
- |
- |
14 |
BRAKE ACTUATOR BRACKET CUSHION |
44547B |
- |
- |
- |
*1 |
BRAKE ACTUATOR BRACKET ASSEMBLY |
- |
- |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Skid control ECU (brake actuator assembly) |
Update ECU security key |
Vehicle Control History (RoB) are stored |
|
Perform "Calibration" |
|
||
Operate the electric parking brake switch |
Electric Parking Brake System |
HINT:
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front camera system
Drive the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
Stop and start system
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
.gif)
- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
PROCEDURE
1. PRECAUTION
![]() |
NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Click here |
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
3. DRAIN BRAKE FLUID
![]() |
NOTICE: If brake fluid leaks onto any painted surface, immediately wash it off. |
4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here ![]()
5. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
Click here ![]()
6. REMOVE WATER GUARD PLATE
Click here ![]()
7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
Click here ![]()
8. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here ![]()
9. REMOVE DASH PANEL HEAT INSULATOR
10. DISCONNECT BRAKE LINE
*a |
From 1st Chamber of Brake Master Cylinder Sub-assembly |
*b |
From 2nd Chamber of Brake Master Cylinder Sub-assembly |
*c |
To Front Wheel Cylinder Assembly RH |
*d |
To Rear Wheel Cylinder Assembly LH |
*e |
To Rear Wheel Cylinder Assembly RH |
*f |
To Front Wheel Cylinder Assembly LH |
![]() |
Release the lock lever |
![]() |
Disconnect the connector |
(1) Release the lock lever and disconnect the connector from the brake actuator assembly.
NOTICE:
Be careful not to allow any brake fluid to enter the connector.
(2) Use tags or make a memo to identify the places to reconnect the brake lines.
(3) Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.
NOTICE:
- Do not kink or damage the brake lines.
- Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
(4) Disengage the 5 clamps to remove the No. 1 brake tube clamp from the brake lines.
NOTICE:
Do not kink or damage the brake lines.
11. REMOVE BRAKE ACTUATOR WITH BRACKET
(1) Remove the 2 nuts.
(2) Remove the bolt and brake actuator with bracket.
NOTICE:
- Do not kink or damage the brake lines.
- Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
- Be careful not to allow any brake fluid to enter the connector.
- Do not hold the brake actuator assembly by the connector.
- Do not drop the brake actuator with bracket when carrying it.
- Remove the brake actuator with bracket while avoiding the brake lines.
12. REMOVE BRAKE ACTUATOR ASSEMBLY
(1) Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.
NOTICE:
- Do not hold the brake actuator assembly by the connector.
- Be careful not to allow any brake fluid to enter the connector.
- Do not drop the brake actuator assembly when carrying it.
13. REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR
14. REMOVE BRAKE ACTUATOR BRACKET CUSHION

.png)
.png)
.png)

