Removal
REMOVAL
COMPONENTS (REMOVAL)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
SECURE VEHICLE |
- |
- |
- |
|
2 |
AUXILIARY BATTERY |
- |
- |
- |
- |
3 |
ECM |
89661 |
- |
- |
- |
4 |
BATTERY CLAMP SUB-ASSEMBLY |
74404A |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
5 |
FRONT FLOOR CENTER BRACE |
57533B |
- |
- |
- |
6 |
FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
17410 |
- |
- |
|
7 |
FRONT LOWER NO. 1 FLOOR HEAT INSULATOR |
58152A |
- |
- |
- |
● |
Non-reusable part |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
8 |
SHIFT LOCK RELEASE BUTTON COVER |
33554C |
- |
- |
|
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
9 |
CONSOLE BOX ASSEMBLY |
58810J |
- |
- |
- |
10 |
NO. 3 CONSOLE BOX DUCT |
58863A |
- |
- |
- |
11 |
NO. 2 CONSOLE BOX DUCT |
58862B |
- |
- |
- |
12 |
NO. 1 CONSOLE BOX DUCT |
58861B |
- |
- |
- |
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
13 |
DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Shift Lever Side) |
33820B |
- |
- |
|
14 |
DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Transaxle Side) |
33820B |
- |
- |
|
15 |
REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY |
33820B |
- |
- |
- |
● |
Non-reusable part |
- |
- |
CAUTION:
- When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
.png)
- Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
- Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front camera system
Drive the vehicle straight ahead at 15 km/h or more for 1 second or more.
.gif)
Stop and start system
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
.gif)
- Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
.gif)
Power back door system
Fully close the back door by hand.
HINT:
Initialization is not necessary if the above procedures are performed while the back door is closed.
.gif)
Air conditioning system
After the ignition switch is turned to ON, the servo motor standard position is recognized.
-
PROCEDURE
1. SECURE VEHICLE
![]() |
Click here |
2. REMOVE AUXILIARY BATTERY
Click here ![]()
3. REMOVE ECM
Click here ![]()
4. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here ![]()
5. REMOVE FRONT FLOOR CENTER BRACE
Click here ![]()
6. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
![]() |
Click here |
7. REMOVE FRONT LOWER NO. 1 FLOOR HEAT INSULATOR
Click here ![]()
8. REMOVE SHIFT LOCK RELEASE BUTTON COVER
![]() |
Click here |
9. REMOVE CONSOLE BOX ASSEMBLY
Click here ![]()
10. REMOVE NO. 3 CONSOLE BOX DUCT
Click here ![]()
11. REMOVE NO. 2 CONSOLE BOX DUCT
Click here ![]()
12. REMOVE NO. 1 CONSOLE BOX DUCT
Click here ![]()
13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Shift Lever Side)
![]() |
Click here |
14. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Transaxle Side)
![]() |
Click here |
15. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
(1) Remove the nut.
(2) Disengage the guide to separate the transmission control cable assembly from the vehicle body.
(3) Remove the 2 nuts and transmission control cable assembly from the vehicle body.
.png)
.png)
.png)