Terminals Of Ecu
TERMINALS OF ECU
NOTICE:
- When performing an inspection, make sure that "ACC Customize" is set to "ON" using the multi-display.
Click here
.gif)
- When "ACC Customize" is set to "ON" (ACC supply power enabled), the certification ECU (smart key ECU assembly) controls the ACC relay on and off. When "ACC Customize" is set to "OFF" (ACC supply power disabled), the certification ECU (smart key ECU assembly) and radio and display receiver assembly control the ACC relay on and off.
Therefore, inspection conditions and results may differ depending on whether "ACC customize" is set to ON or OFF when inspecting ACC related terminals.
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Disconnect the I223 and I222 certification ECU (smart key ECU assembly) connectors.
(b) Measure the resistance and voltage according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Tester Connection | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|
I223-15 (NE) - Body ground |
Engine speed signal |
Always |
10 kΩ or higher |
Engine Condition |
I223-21 (STP1) - Body ground |
Stop light switch signal |
Brake pedal depressed → Brake pedal released |
9 V or higher → 1 V or less |
Power Source Control
|
I222-6 (+B) - I222-29 (E) |
Power source |
Ignition switch off |
11 to 14 V |
- |
I222-14 (P) - I222-29 (E) |
P position signal |
Shift lever in P → Shift lever not in P |
30 kΩ or higher → Below 200 Ω |
Power Source Control
|
I223-22 (CUTB) - Body ground |
Dark current cut pin* |
Ignition switch off |
11 to 14 V |
- |
I222-29 (E) - Body ground |
GND |
Always |
Below 1 Ω |
- |
I222-23 (SSW3) - Body ground |
SSW3 contact signal |
Engine switch pushed → Engine switch not pushed |
Below 15 Ω → 10 kΩ or higher |
Power Source Control
|
I222-27 (SSW2) - Body ground |
SSW2 contact signal |
Engine switch pushed → Engine switch not pushed |
Below 15 Ω → 10 kΩ or higher |
Power Source Control
|
I222-19 (SSW1) - Body ground |
SSW1 contact signal |
Engine switch pushed → Engine switch not pushed |
Below 15 Ω → 10 kΩ or higher |
Power Source Control
|
I223-13 (SPD) - Body ground |
Vehicle speed signal |
Always |
30 kΩ or higher |
Vehicle Speed Signal |
- *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).
(c) Connect the I223 and I222 certification ECU (smart key ECU assembly) connectors.
(d) Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
Tester Connection | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|
I223-3 (STA) - I222-29 (E) |
When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". |
Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) |
6 V or higher*2 → 1.0 V or less |
- |
I223-10 (STAR) -I222-29 (E) |
Outputs voltage to the starter relay
HINT: When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input. |
Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) |
6 V or higher*2 → 1.0 V or less |
- |
I223-10 (STAR) -I222-29 (E) |
Receives neutral start switch (P, N position detection) signal
|
Perform the following operations except while the engine is cranking:
|
9 V or higher → 2.7 V or less |
Neutral SW/ Clutch SW |
I223-15 (NE) - I222-29 (E) |
Engine speed signal |
Idling (engine warmed up) |
Pulse generation (See waveform 1) |
Engine Condition |
I223-21 (STP1) -I222-29 (E) |
Stop light switch signal |
Brake pedal released → Brake pedal depressed |
1 V or less → 9 V or higher |
Stop Light Switch1 |
I222-11 (SLP) - Body Ground |
GND |
Always |
Below 1 Ω |
- |
I222-8 (LIN) - I222-29 (E) |
LIN communication line |
Ignition switch ON |
Pulse generation |
Smart Key
|
I222-14 (P) - I222-29 (E) |
P position signal |
Shift lever in P → Shift lever not in P |
9 V or higher → 2.76 V or less |
Power Source Control
|
I222-23 (SSW3) - I222-29 (E) |
SSW3 contact signal |
Engine switch not pushed → Engine switch pushed |
9 V or higher → 1 V or less |
Power Source Control
|
I222-27 (SSW2) - I222-29 (E) |
SSW2 contact signal |
Engine switch not pushed → Engine switch pushed |
9 V or higher → 1 V or less |
Power Source Control
|
I222-19 (SSW1) - I222-29 (E) |
SSW1 contact signal |
Engine switch not pushed → Engine switch pushed |
9 V or higher → 1 V or less |
Power Source Control
|
I222-21 (ACCD) - I222-29 (E) |
ACC signal |
Ignition switch off → Ignition switch ACC |
1 V or less → 8.5 V or higher |
Power Source Control
|
I223-11 (IGRD) - I222-29 (E) |
IG signal |
Ignition switch off → Ignition switch ON |
1 V or less → 9 V or higher |
Power Source Control
|
I223-24 (IGPD) - I222-29 (E) |
IG signal |
Ignition switch off → Ignition switch ON |
1 V or less → 9 V or higher |
Power Source Control
|
I223-13 (SPD) - I222-29 (E) |
Vehicle speed signal |
Vehicle being driven at approx. 5 km/h |
Pulse generation (See waveform 1) |
Power Source Control
|
I222-4 (CLG5) - I222-29 (E) |
Output to No. 1 indoor electrical key antenna assembly (front floor) |
Procedure:
|
Pulse generation (See waveform 2) |
- |
I222-5 (CG5B) - I222-29 (E) |
Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) |
Procedure:
|
Pulse generation (See waveform 2) |
- |
O200-10 (CLG7) - I222-29 (E) |
Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) |
Procedure:
|
Pulse generation (See waveform 2) |
- |
O200-9 (CG7B) - I222-29 (E) |
Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) |
Procedure:
|
Pulse generation (See waveform 2) |
- |
I222-30 (AGND) - Body ground |
Transponder key amplifier ground |
Always |
Below 1 Ω |
- |
I222-12 (ANT1) - I222-30 (AGND) |
Signal input / output from transponder key coil (transponder key coil built into engine switch) |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
Pulse generation (See waveform 3) |
Smart Key
|
I222-13 (ANT2) - I222-30 (AGND) |
Signal input / output from transponder key coil (transponder key coil built into engine switch) |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
Pulse generation (See waveform 4) |
|
I222-25 (IND) - I222-29 (E) |
Security indicator output |
Ignition switch off → ON |
Pulse generation → Below 2 V |
- |
O200-20 (WCSW) - I222-29 (E)* |
Wireless charger system stop signal |
Procedure:
|
Below 1 V → 4.5 to 6 V (For 1 second after ignition switch to ACC) |
- |
- *: w/ Wireless Charging System
HINT:
- *2: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.
- The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.
- The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:
- To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the ignition switch to ACC or ON.
- To lock the steering, open a door with the ignition switch off and the shift lever in P.
(e) Using an oscilloscope, check the waveform of the ECU.
NOTICE:
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
(1) Waveform 1
Measurement Condition Item | Content |
|---|---|
Tester Connection |
I223-13 (SPD) - I222-29 (E) |
Tool Setting |
5 V/DIV., 20 ms./DIV. |
Condition |
Vehicle being driven at approx. 5 km/h |
HINT:
The wavelength becomes shorter as the vehicle speed increases.
(2) Waveform 2
*a |
For 30 seconds after any door closed |
*b |
After 30 seconds or more have elapsed since any door closed |
Item | Content |
|---|---|
Tester Connection |
I222-4 (CLG5) - I222-29 (E) I222-5 (CG5B) - I222-29 (E) O200-2 (CG6B) - I222-29 (E) O200-1 (CLG6) - I222-29 (E) O200-10 (CLG7) - I222-29 (E) O200-9 (CG7B) - I222-29 (E) |
Tool Setting |
5 V/DIV., 500 ms./DIV. |
Condition |
Procedure:
|
(3) Waveform 3
Measurement Condition Item | Content |
|---|---|
Tester Connection |
I222-12 (ANT1) - I222-30 (AGND) |
Tool Setting |
5 V/DIV., 200 ms./DIV. |
Condition |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
(4) Waveform 4
Measurement Condition Item | Content |
|---|---|
Tester Connection |
I222-13 (ANT2) - I222-30 (AGND) |
Tool Setting |
20 V/DIV., 200 ms./DIV. |
Condition |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
CHECK ID CODE BOX (IMMOBILISER CODE ECU)
(a) Disconnect the I20 ID code box (immobiliser code ECU) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Tester Connection | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|
I20-1 (+B) - Body ground |
Power source |
Ignition switch off |
11 to 14 V |
- |
I20-5 (GND) - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the I20 ID code box (immobiliser code ECU) connector.
(d) Measure the voltage and check for pulses according to the value(s) in the table below.
Tester Connection | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|
I20-3 (EFII) - I20-5 (GND) |
EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU)) |
Ignition switch off |
11 to 14 V |
Smart Key
|
I20-3 (EFII) - I20-5 (GND) |
EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU)) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
Pulse generation (See waveform 1) |
|
I20-4 (EFIO) - I20-5 (GND) |
EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM) |
Ignition switch off |
Below 1 V |
|
I20-4 (EFIO) - I20-5 (GND) |
EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
Pulse generation (See waveform 2) |
|
I20-2 (LIN1) - I20-5 (GND) |
LIN communication line |
Ignition switch ON |
Pulse generation |
Smart Key
|
(e) Using an oscilloscope, check the waveform.
NOTICE:
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
(1) Waveform 1
*a |
Approximately 160 ms. |
*b |
Approximately 270 ms. |
Item | Content |
|---|---|
Tester Connection |
I20-3 (EFII) - I20-5 (GND) |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
(2) Waveform 2
*a |
Approximately 160 ms. |
*b |
Approximately 270 ms. |
Item | Content |
|---|---|
Tester Connection |
I20-4 (EFIO) - I20-5 (GND) |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
CHECK ECM
(a) Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|
A47-2 (IGP) - A47-10 (E1) |
Ignition power supply |
Ignition switch ON |
11 to 14 V |
- |
A47-14 (IGR) - A47-10 (E1) |
Ignition power supply |
Ignition switch ON |
11 to 14 V |
- |
A47-10 (E1) - Body ground |
Ground |
Always |
Below 1 Ω |
- |
A47-25 (IMO) - A47-10 (E1) |
EFI communication output (Signal output from ECM to ID code box (immobiliser code ECU)) |
Engine switch on (IG) |
11 to 14 V |
|
A47-25 (IMO) - A47-10 (E1) |
EFI communication output (Signal output from ECM to ID code box (immobiliser code ECU)) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
Pulse generation (See waveform 1) |
|
A47-26 (IMI) - A47-10 (E1) |
EFI communication input (Signal input from ID code box (immobiliser code ECU) to ECM) |
Engine switch on (IG) |
Below 1 V |
|
A47-26 (IMI) - A47-10 (E1) |
EFI communication input (Signal input from ID code box (immobiliser code ECU) to ECM) |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
Pulse generation (See waveform 2) |
(b) Using an oscilloscope, check the waveform.
NOTICE:
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
(1) Waveform 1 (Reference)
*a |
Approximately 160 ms. |
*b |
Approximately 270 ms. |
Item | Content |
|---|---|
Tester Connection |
A47-25 (IMO) - A47-10 (E1) |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
(2) Waveform 2 (Reference)
*a |
Approximately 160 ms. |
*b |
Approximately 270 ms. |
Item | Content |
|---|---|
Tester Connection |
A47-26 (IMI) - A47-10 (E1) |
Tool Setting |
2 V/DIV., 500 ms./DIV. |
Condition |
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to auxiliary battery |
CHECK ENGINE SWITCH
(a) Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|
I35-3 (GND) - Body ground |
Transponder key amplifier ground |
Always |
Below 1 Ω |
- |
(b) Measure the voltage and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
|---|---|---|---|---|
I35-1 (ANT1) - I35-3 (GND) |
Signal input / output from transponder key coil (transponder key coil built into engine switch) |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
Pulse generation (See waveform 1) |
Smart Key
|
I35-7 (ANT2) - I35-3 (GND) |
Signal input / output from transponder key coil (transponder key coil built into engine switch) |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
Pulse generation (See waveform 2) |
|
I35-11 (SS3) - I35-3 (GND) |
SS3 contact signal HINT: Backup for SS1. Behaves the same way as SS1. |
Engine switch not pushed → Engine switch pushed |
9 V or higher → Below 1 V |
Power Source Control
|
I35-6 (SS2) - I35-3 (GND) |
SS2 contact signal HINT: Backup for SS1. Behaves the same way as SS1. |
Engine switch not pushed → Engine switch pushed |
9 V or higher → Below 1 V |
Power Source Control
|
I35-12 (SS1) - I35-3 (GND) |
SS1 contact signal |
Engine switch not pushed → Engine switch pushed |
9 V or higher → Below 1 V |
Power Source Control
|
(c) Using an oscilloscope, check the waveform.
NOTICE:
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
(1) Waveform 1 (Reference)
Measurement Condition Item | Content |
|---|---|
Tester Connection |
I35-1 (ANT1) - I35-3 (GND) |
Tool Setting |
20 V/DIV., 200 ms./DIV. |
Condition |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
(2) Waveform 2 (Reference)
Measurement Condition Item | Content |
|---|---|
Tester Connection |
I35-7 (ANT2) - I35-3 (GND) |
Tool Setting |
20 V/DIV., 200 ms./DIV. |
Condition |
Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed |
SMART KEY SYSTEM (for Entry Function)
Click here ![]()