Warning Notification Function Malfunction
PROCEDURE
CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION)
(a) Check the problem symptom.
(1) Check the problem symptom of the warning notification function.
Result | Proceed to |
|---|---|
The multi-display screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning (for HEV Model). |
A |
The multi-display screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning (for Gasoline Model). |
B |
The multi-display screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning. |
C |
The multi-display screen shows a warning message different from the warning light or the multi-information display. |
HINT:
- The warning notification function sends information to the service center through communication.
- Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.
| B | GO TO STEP 6 |
| C | GO TO STEP 8 |
|
INSPECT WARNING LIGHT
(a) Check if the indicated warning light or message is listed in the following table.
HINT:
Only messages listed in the table are included in the warning notification function.
Warning Name |
|---|
Engine warning |
Brake system warning |
VSC warning |
ABS warning |
ECB warning |
EPS warning |
Charging system warning |
Airbag warning |
PCS warning |
Cruise warning |
Intuitive parking assist system |
Drive start control system |
Brake override system warning |
Smart key system warning |
Front-lighting adaptive system warning |
Automatic headlight beam level control system warning |
Automatic high beam system warning |
LED headlight warning |
Transmission fluid temperature warning |
4WD system warning |
Tire pressure system warning |
Electric parking brake warning |
Auto hold warning |
Blind spot monitor system warning |
Advanced park warning |
Secondary collision brake warning |
Engine maintenance waring |
LTA system warning |
Flashing hazard light system warning |
RSA system warning |
RCTA warning |
Power running board system warning |
Engine oil level warning |
Engine oil pressure warning |
Tire pressure low warning |
Washer fluid level warning |
Engine oil maintenance warning |
High coolant temperature warning |
Maintenance advice warning |
Engine shutdown forgotten warning |
Hybrid control system warning |
Acoustic vehicle alerting system warning |
Brake fluid warning |
Hybrid system temperature warning |
Hybrid battery cooling fan maintenance warning |
Result | Proceed to |
|---|---|
Warning light or message is listed in the table. |
A |
Warning light or message is not listed in the table. |
B |
| B | END |
|
CHECK CAN COMMUNICATION SYSTEM
(a) Enter the following menus: Bus Check.
(b) Check that all ECUs and sensors that use CAN communication are connected.
Click here ![]()
Result | Proceed to |
|---|---|
There are no connection problems. |
A |
There is a connection problem. |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK METER WARNING LIGHT
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
| NG | GO TO METER / GAUGE SYSTEM |
|
CHECK AUDIO AND VISUAL SYSTEM
(a) Check if the audio and visual system is operating and functioning normally.
OK:
The audio and visual system is normal.
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | GO TO AUDIO AND VISUAL SYSTEM |
INSPECT WARNING LIGHT
(a) Check if the indicated warning light or message is listed in the following table.
HINT:
Only messages listed in the table are included in the warning notification function.
Warning Name |
|---|
Engine warning |
Brake system warning |
VSC warning |
ABS warning |
ECB warning |
EPS warning |
Charging system warning |
Airbag warning |
PCS warning |
Cruise warning |
Intuitive parking assist system warning |
Drive start control system |
Brake override system warning |
Smart key system warning |
Adaptive front-lighting system warning |
Automatic high beam system warning |
LED headlight warning |
Transmission fluid temperature warning |
Dynamic torque control AWD system warning |
Tire pressure system warning |
Electric parking brake warning |
Auto hold warning |
Blind spot monitor system warning |
Engine stop and start system warning |
Advanced park warning |
Secondary collision brake warning |
Engine maintenance warning |
LTA system warning |
RSA system warning |
RCTA warning |
Engine oil level warning |
Brake fluid warning |
Engine oil pressure warning |
Tire pressure low warning |
Washer fluid level warning |
Engine oil maintenance warning |
High coolant temperature warning |
Maintenance advice warning |
Engine shutdown forgotten warning |
Result | Proceed to |
|---|---|
Warning light or message is listed in the table. |
A |
Warning light or message is not listed in the table. |
B |
| B | END |
|
CHECK CAN COMMUNICATION SYSTEM
(a) Enter the following menus: Bus Check.
(b) Check that all ECUs and sensors that use CAN communication are connected.
Click here ![]()
Result | Proceed to |
|---|---|
There are no connection problems. |
A |
There is a connection problem. |
B |
| A | GO TO STEP 4 |
| B | GO TO CAN COMMUNICATION SYSTEM |
CHECK METER WARNING LIGHT
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
| OK | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
| NG | GO TO METER / GAUGE SYSTEM |