Toyota Corolla Quiz
Diagnostics

Inspection procedure

In this manual: Diagnostics
Introduction — 31Preparation — 32Service specifications — 19Diagnostics — 497Engine control system — 6Fuel — 13Emission control — 28Exhaust — 3Cooling — 13Lubrication — 7Ignition — 3Starting & charging — 13Front suspension — 12Rear suspension — 9Tire & wheel — 1Drive shaft / propeller shaft — 15Brake — 42Automatic transmission / trans — 47Clutch — 19Steering column — 9Power steering — 11Heater & air conditioner — 20Supplemental restraint system — 27Seat belt — 12Lighting — 18Wiper & washer — 9Audio & visual — 12Wiring — 1Communication system — 1Windshield/windowglass/mirror — 31Seat — 10Theft deterrent & door lock — 10Sliding roof/convertible — 8Engine hood/door — 12Exterior/interior trim — 20Vehicle control system — 1Cruise control — 5Maintenance — 8
20steps
~120min
4/5difficulty
Done 0 of 20
1 Check wire harness(airbag sensor assy center – front seat inner belt assy lh)
Toyota Corolla. Check wire harness
  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. disconnect the connectors between the airbag sensor assy center and the front seat inner belt assy (lh).
  3. for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the front seat inner belt assy (lh), measure the resistance between lbe+ and body ground.

    Ok: resistance: 1 mw or higher

    2 Check wire harness(airbag sensor assy center – front seat inner
2 Check wire harness(airbag sensor assy center – front seat inner belt assy lh)
Toyota Corolla. Check wire harness
  1. Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  2. turn the ignition switch to on.
  3. for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the front seat inner belt assy (lh), measure the voltage between lbe+ and body ground.

    Ok: voltage: below 1 v

    3 Check front seat inner belt assy lh
3 Check front seat inner belt assy lh
Toyota Corolla. Check front seat inner belt assy lh
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. connect the connector of the front seat inner belt assy (lh).
  4. unlock the seat belt for the front driver’s seat.
  5. for the connector (on the airbag sensor assy center side), measure the resistance between lbe+ and body ground.

    Ok: resistance: 1.0 Kw – 1.6 KΩ

    4 Check front seat inner belt assy lh
4 Check front seat inner belt assy lh
Toyota Corolla. Check front seat inner belt assy lh
  1. Lock the seat belt for the front driver’s seat.
  2. for the connector (on the airbag sensor assy center side), measure the resistance between lbe+ and body ground.

    Ok: resistance: 100 w – 500 Ω

    5 Check air bag sensor assy center
5 Check air bag sensor assy center

Sst 09843–18040

Toyota Corolla. Check air bag sensor assy center
  1. Connect the connector to the airbag sensor assy center.
  2. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  3. turn the ignition switch to on, and wait at least for 20 seconds.
  4. clear the dtc stored in memory .
  5. turn the ignition switch to lock, and wait at least for 20 seconds.
  6. turn the ignition switch to on, and wait at least for 20 seconds.
  7. check the dtc .

    Ok: dtc b0126/b0127/27 is not output.

Hint

: codes other than code b0126/b0127/27 may be output at this time, but they are not relevant to this check.
Use simulation method to check
Use simulation method to check

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.