Inspection procedure

Sst 09843–18040

1. 1
   Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
2. 2
   turn the ignition switch to on, and wait at least for 20 seconds.
3. 3
   clear the dtc stored in memory .
4. 4
   turn the ignition switch to lock, and wait at least for 20 seconds.
5. 5
   turn the ignition switch to on, and wait at least for 20 seconds.
6. 6
   check the dtc .

   Ok: dtc b1141/33 is not output.

   

   

1. 1
   Turn the ignition switch to lock.
2. 2
   disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
3. 3
   check that the connectors is properly connected to the airbag sensor assy center.

   

   

1. Check that the connector is properly connected to the side airbag sensor assy (lh).

Sst 09843–18040

1. 1
   Disconnect the connectors between the airbag sensor assy center and the side airbag sensor assy lh.
2. 2
   using a service wire, connect vupl and esl, and fsl and ssl– of the connector (on the side airbag sensor assy side) between the airbag sensor assy center and the side airbag sensor assy (lh).
3. 3
   for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (lh), measure the resistance between vupl and esl, and between fsl and ssl–.

   Ok: resistance: below 1 w

   

   

1. 1
   Disconnect the connection between vupl and esl, and between fsl and ssl–.
2. 2
   for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (lh), measure the resistance between each terminal of vupl, ssl– and fsl, and body ground.

   Ok: resistance: 1mΩ or higher

   

   

1. For the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (lh), measure the resistance between vupl and esl, and between fsl and ssl–.

   Ok: resistance: 1mΩ or higher

1. 1
   Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
2. 2
   turn the ignition switch to on.
3. 3
   for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the side airbag sensor assy (lh), measure the voltage between each terminal of vupl, ssl– and fsl, and body ground.

   Ok: voltage: below 1v

   

   

Sst 09843–18040

1. 1
   Turn the ignition switch to lock.
2. 2
   disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
3. 3
   connect the airbag sensor assy center connector.
4. 4
   interchange the side airbag sensor assy (lh) and rh and connect the connectors to them.
5. 5
   connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
6. 6
   turn the ignition switch to on, and wait at least for 20 seconds.
7. 7
   clear the dtc stored in memory .
8. 8
   turn the ignition switch to lock, and wait at least for 20 seconds.
9. 9
   turn the ignition switch to on, and wait at least for 20 seconds.
10. 10
    check the dtc .

    Ok: (a): dtc b1140/32 is not output.

    (B): dtc b1141/33 is not output.