Toyota Corolla Quiz
Diagnostics

Inspection procedure

In this manual: Diagnostics
Introduction — 31Preparation — 32Service specifications — 19Diagnostics — 497Engine control system — 6Fuel — 13Emission control — 28Exhaust — 3Cooling — 13Lubrication — 7Ignition — 3Starting & charging — 13Front suspension — 12Rear suspension — 9Tire & wheel — 1Drive shaft / propeller shaft — 15Brake — 42Automatic transmission / trans — 47Clutch — 19Steering column — 9Power steering — 11Heater & air conditioner — 20Supplemental restraint system — 27Seat belt — 12Lighting — 18Wiper & washer — 9Audio & visual — 12Wiring — 1Communication system — 1Windshield/windowglass/mirror — 31Seat — 10Theft deterrent & door lock — 10Sliding roof/convertible — 8Engine hood/door — 12Exterior/interior trim — 20Vehicle control system — 1Cruise control — 5Maintenance — 8
45steps
~270min
4/5difficulty
Done 0 of 45
1 Check seat position air bag sensor

Sst 09843–18040

Toyota Corolla. Check seat position air bag sensor
  1. Turn the ignition switch to on, and wait at least for 20 seconds.
  2. clear the dtc stored in memory .
  3. turn the ignition switch to lock, and wait at least for 20 seconds.
  4. turn the ignition switch to on, and wait at least for 20 seconds.
  5. check the dtc .

    Ok: dtc b1153/25 is not output.

Hint

: codes other than code b1153/25 may be output at this time, but they are not relevant to this check.
2 Check airbag sensor assy center connector
2 Check airbag sensor assy center connector
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. check that the connector is properly connected to the airbag sensor assy center.
    3 Check seat position airbag sensor connector
3 Check seat position airbag sensor connector
  1. Check that the connector is properly connected to the seat position airbag sensor.
4 Check seat position airbag sensor circuit (open)(airbag sensor
4 Check seat position airbag sensor circuit (open)(airbag sensor assy center – seat position airbag sensor)

Sst 09843–18040

Toyota Corolla. Check seat position airbag sensor circuit
  1. Disconnect the connectors between the airbag sensor assy center and the seat position airbag sensor.
  2. using a service wire, connect lsp+ and lsp– of the connector (on the seat position airbag sensor side) between the airbag sensor assy center and the seat position airbag sensor.
  3. for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position airbag sensor, measure the resistance between lsp+ and lsp–.

    Ok: resistance: below 1 Ω

    5 Check seat position airbag sensor circuit (to ground)(airbag
5 Check seat position airbag sensor circuit (to ground)(airbag sensor assy center – seat position airbag sensor)
Toyota Corolla. Check seat position airbag sensor circuit
  1. Release the service wire of the connector (on the seat position airbag sensor side) between the seat position airbag sensor and the airbag sensor assy center.
  2. for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position airbag sensor, measure the resistance between body ground and each of lsp+ and lsp–.

    Ok: resistance: 1 mΩ or higher

    6 Check seat position airbag sensor circuit(airbag sensor assy
6 Check seat position airbag sensor circuit(airbag sensor assy center – seat position airbag sensor)
Toyota Corolla. Check seat position airbag sensor circuit
  1. For the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position airbag sensor, measure the resistance between lsp+ and lsp–.

    Ok: resistance: 1 mΩ or higher

7 Check seat position airbag sensor circuit (to b+)(airbag sensor
7 Check seat position airbag sensor circuit (to b+)(airbag sensor assy center – seat position airbag sensor)
Toyota Corolla. Check seat position airbag sensor circuit
  1. Connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  2. turn the ignition switch to on.
  3. for the connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position airbag sensor, measure the voltage between the body ground and each of lsp+ and lsp–.

    Ok: voltage: below 1 v

    8 Check seat position air bag sensor
8 Check seat position air bag sensor

Sst 09843–18040

Toyota Corolla. Check seat position air bag sensor
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. connect the connectors of the seat position airbag sensor and the airbag sensor assy center.
  4. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on, and wait at least for 20 seconds.
  6. clear the dtc stored in memory .
  7. turn the ignition switch to lock, and wait at least for 20 seconds.
  8. turn the ignition switch to on, and wait at least for 20 seconds.
  9. check the dtc .

    Ok: dtc d1153/25 is not output.

Hint

: codes other that code b1153/25 may be output at this time, but they are not relevant to this check.
Use simulation method to check
Use simulation method to check 9 Check air bag sensor assy center

Sst 09843–18040

Toyota Corolla. Check air bag sensor assy center
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. connect the connector of a new seat position airbag sensor.
  4. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on, and wait at least for 20 seconds.
  6. clear the dtc stored in memory .
  7. turn the ignition switch to lock, and wait at least for 20 seconds.
  8. turn the ignition switch to on, and wait at least for 20 seconds.
  9. check the dtc .

    Ok: dtc d1153/25 is not output.

Hint

: codes other that code b1153/25 may be output at this time, but they are not relevant to this check.
Use simulation method to check
Use simulation method to check 10 Check wire harness(seat position airbag sensor – front seat inner belt assy)

Sst 09843–18040

  1. Disconnect the front seat wire connector on the airbag sensor assy center side.
  2. for the front seat wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position airbag sensor, measure the resistance between lsp+ and lsp–.

    Ok: resistance: below 1 Ω

    Repair or replace instrument panel wire no.3(Airbag sensor assy center –
Repair or replace instrument panel wire no.3(Airbag sensor assy center – front seat inner belt assy) 11 Check wire harness(seat position airbag sensor – front seat inner belt assy)
  1. Disconnect the front seat wire connector on the airbag sensor assy center side.
  2. for the front seat wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position sensor, measure the resistance between body ground and each of lsp+ and lsp–.

    Ok: resistance: 1 mΩ or higher

    Repair or replace instrument panel wire no.3(Airbag sensor assy center –
Repair or replace instrument panel wire no.3(Airbag sensor assy center – front seat inner belt assy) 12 Check wire harness(seat position airbag sensor – front seat inner belt assy)
Toyota Corolla. Check wire harness
  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. disconnect the front seat wire connector on the airbag sensor assy center side.
  3. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4. turn the ignition switch to on, and wait at least for 60 seconds.
  5. for the front seat wire connector (on the airbag sensor assy center side) between the front seat inner belt assy and the seat position airbag sensor, measure the voltage between body ground and each of lsp+ and lsp–.

    Ok: voltage: below 1 v

    Repair or replace instrument panel wire no.3(Airbag sensor assy center –
Repair or replace instrument panel wire no.3(Airbag sensor assy center – front seat inner belt assy) 13 Check wire harness(seat position airbag sensor – front seat inner belt assy)
Toyota Corolla. Check wire harness
  1. Turn the ignition switch to lock.
  2. for the front seat wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the seat position sensor, measure the resistance between lsp+ and lsp–.

    Ok: resistance: 1 mΩ or higher

    Repair or replace instrument panel wire no.3(Airbag sensor assy center –
Repair or replace instrument panel wire no.3(Airbag sensor assy center – front seat inner belt assy)

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.