Diagnostics

Inspection procedure

29steps
~174min
4/5difficulty
Done 0 of 29
1 Check front airbag sensor (lh) circuit (to b+)(airbag sensor assy center – airbag sensor front lh)
Toyota Corolla. Check front airbag sensor (lh) circuit
  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. disconnect the connectors between the airbag sensor assy center and the airbag sensor front lh.
  3. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4. ) turn the ignition switch to on.
  5. for the connector (on the airbag sensor assy center side) between the airbag sensor front lh and the airbag sensor assy center, measure the voltage between body ground and each of +sl and –sl.

    Ok: voltage: below 1 v

    2 Check front airbag sensor(lh) circuit(to ground)(airbag sensor
2 Check front airbag sensor(lh) circuit(to ground)(airbag sensor assy center – airbag sensor front lh)
Toyota Corolla. Check front airbag sensor(lh) circuit
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. for the connector (on the airbag sensor assy center side) between the airbag sensor front lh and the airbag sensor assy center, measure the resistance between body ground and each of +sl and –sl.

    Ok: resistance: 1 mΩ or higher

    3 Check front airbag sensor (lh) circuit(open)(airbag sensor assy
3 Check front airbag sensor (lh) circuit(open)(airbag sensor assy center – airbag sensor front lh)
Toyota Corolla. Check front airbag sensor (lh) circuit
  1. Using a service wire, connect +sl and –sl of the connector (on the airbag sensor front lh side) between the airbag sensor assy center and the airbag sensor front lh.
  2. for the connector (on the airbag sensor assy center side) between the airbag sensor front lh and the airbag sensor assy center, measure the resistance between +sl and –sl.

    Ok: resistance: below 1 Ω

    4 Inspect air bag sensor front lh
4 Inspect air bag sensor front lh
Toyota Corolla. Inspect air bag sensor front lh
  1. For the connector of the airbag sensor front lh, measure the resistance between +sl and –sl.

    Ok: resistance: 820 Ω

5 Check air bag sensor assy center
5 Check air bag sensor assy center

Sst 09843–18040

Toyota Corolla. Check air bag sensor assy center
  1. Disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  2. connect the airbag sensor front lh connector and airbag sensor assy center connector.
  3. connect the negative (–) terminal cable to the battery, and wait at least for 2 seconds.
  4. turn the ignition switch to on, and wait at least for 20 seconds.
  5. clear the dtc stored in memory .
  6. turn the ignition switch to lock, and wait at least for 20 seconds.
  7. turn the ignition switch to on, and wait at least for 20 seconds.
  8. check the dtc .

    Ok: dtc b1158/b1159/16 is not output.

Hint

: codes other than code b1158/b1159/16 may be output at this time, but they are not relevant to this check.

Use simulation method to check
Use simulation method to check 6 Check engine room main wire harness (to b+)(conector – airbag sensor front lh)
Toyota Corolla. Check engine room main wire harness
  1. Turn the ignition switch to lock.
  2. disconnect the negative (–) terminal cable from the battery, and wait at least for 90 seconds.
  3. disconnect the connector between the engine room main wire and the instrument panel wire.
  4. connect the negative (–) terminal to the battery, and wait at least for 2 seconds.
  5. turn the ignition switch to on.
  6. for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag sensor front lh, measure the voltage between body ground and each of +sl and –sl.

    Ok: voltage: below 1 v

    Repair or replace instrument panel wire
Repair or replace instrument panel wire 7 Check engine room main wire harness (to ground)(connector – airbag sensor front lh)
Toyota Corolla. Check engine room main wire harness
  1. Disconnect the connectors between the engine room main wire and the instrument panel wire.
  2. for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag sensor front lh, measure the resistance between body ground and each of +sl and –sl.

    Ok: resistance: 1 mw or higher

    Repair or replace instrument panel wire
Repair or replace instrument panel wire 8 Check engine room main wire harness(open)(connector – airbag sensor front lh)
Toyota Corolla. Check engine room main wire harness
  1. Disconnect the connectors between the engine room main wire and the instrument panel wire.
  2. using a service wire, connect +sl and –sl of the engine room main wire connector (on the airbag sensor front lh side) between the airbag sensor assy center and the airbag sensor front lh.
  3. for the engine room main wire connector (on the airbag sensor assy center side) between the airbag sensor assy center and the airbag sensor front lh, measure the resistance between +sl and –sl.

    Ok: resistance: below 1 Ω

    Repair or replace instrument panel wire
Repair or replace instrument panel wire

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.