Toyota Corolla Quiz
Front suspension

Stabilizer bar front

In this manual: Front suspension
Introduction — 31Preparation — 32Service specifications — 19Diagnostics — 497Engine control system — 6Fuel — 13Emission control — 28Exhaust — 3Cooling — 13Lubrication — 7Ignition — 3Starting & charging — 13Front suspension — 12Rear suspension — 9Tire & wheel — 1Drive shaft / propeller shaft — 15Brake — 42Automatic transmission / trans — 47Clutch — 19Steering column — 9Power steering — 11Heater & air conditioner — 20Supplemental restraint system — 27Seat belt — 12Lighting — 18Wiper & washer — 9Audio & visual — 12Wiring — 1Communication system — 1Windshield/windowglass/mirror — 31Seat — 10Theft deterrent & door lock — 10Sliding roof/convertible — 8Engine hood/door — 12Exterior/interior trim — 20Vehicle control system — 1Cruise control — 5Maintenance — 8
4steps
~24min
2/5difficulty
Done 0 of 4
Replacement Hint

: components:

 1. Remove front wheel 2. Remove front stabilizer link assy lh
Toyota Corolla. Remove front stabilizer link assy lh
  1. Remove the 2 nuts and stabilizer bar link.
Hint

: if the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.

 3. Remove front stabilizer link assy rh Hint

: remove the rh side by the same procedure as the lh side.

 4. Inspect front stabilizer link assy
Toyota Corolla. Inspect front stabilizer link assy
  1. As shown in the illustration, flip the ball joint stud back and forth 5 times, before installing the nut.
  2. using a torque wrench, turn the nut continuously at a rate of 2 – 4 seconds per 1 turn and take the torque reading on the 5th turn.

    Turning torque: 0.05 – 1.96 Nvm (0.5 – 20 Kgf·cm, 0.4 – 17 In.Vlbf)

5. Separate front suspension arm sub–assy lower no.1 Lh 6. Separate front suspension arm sub–assy lower no.1 Rh Hint

: remove the rh side by the same procedure as the lh side.

 7. Separate rack & pinion power steering gear assy 8. Suspend engine assy at:
mt: 9. Separate front suspension crossmember sub–assy 10. Remove stabilizer bar front
  1. remove the 4 bolts,front stabilizer bracket no.1 Lh, front stabilizer bracket no.1 Rh, 2 front stabilizer bar bushes no.1 And stabilizer bar front from the front suspension crossmember sub–assy.
  2. remove the 2 front stabilizer bar bushes no.1 From the stabilizer bar front.
11. Install stabilizer bar front
Toyota Corolla. Install stabilizer bar front
  1. Install 2 front stabilizer bar bushes no.1, Front stabilizer bracket no.1 Lh and front stabilizer bracket no.1 Rh to the stabilizer bar front.
Hint

: install the bushing to the inner side of the bushing stopper on the stabilizer bar.
Toyota Corolla. Install stabilizer bar front
  1. Install the stabilizer bar front and 4 bolts to the front suspension crossmember sub–assy.

    Torque: 19 nvm (194 Kgf·cm, 14 ft·lbf)

12. Install front suspension crossmember sub–assy sst 09670–00010 13. Install rack & pinion power steering gear assy 14. Install front suspension arm sub–assy lower no.1 Lh 15. Install front suspension arm sub–assy lower no.1 Rh Hint

: install the rh side by the same procedures as the lh side.

 16. Install front stabilizer link assy lh
Toyota Corolla. Install front stabilizer link assy lh
  1. Install the stabilizer bar link with the 2 nuts.

    Torque: 74 nvm (755 Kgf·cm, 55 ft·lbf)

Hint

: if the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.

 17. Install front stabilizer link assy lh Hint

: install the rh side by the same procedure as the lh side.

 18. Install front wheel

torque: 103 nvm (1,050 Kgf·cm, 76 ft·lbf)

19. Inspect and adjust front wheel alignment

Test yourself

A quick Toyota Corolla quiz: every answer comes with an explanation and a link to the manual page.