Installation

1. Install fuel filler opening lid lock retainer

1. 1
   Install the lock retainer and turn it counterclockwise as shown in the illustration.
2. 2
   Install fuel filler opening lid lock retainer

   

1. 1
   Install the cable and turn it clockwise as shown in the illustration.
2. 2
   Install the fuel lid lock open lever with the bolt.

Torque: 8.0 N*m (82 kgf*cm, 71 in.*Lbf)

Install the cable to the clamps as shown in the illustration.

1. 1
   Install front floor carpet assembly
2. 2
   Install deck trim side panel assembly rh (w/ rear no. 2 Seat) (see page ir-34)
3. 3
   Install deck trim side panel assembly rh (w/o rear no. 2 Seat) (see page ir-53)
4. 4
   Install deck trim side panel assembly lh (w/ rear no. 2 Seat) (see page ir-32)
5. 5
   Install deck trim side panel assembly lh (w/ o rear no. 2 Seat) (see page ir-52)
6. 6
   Install tether anchor bracket subassembly (w/o rear no. 2 Seat) (see page ir-54)
7. 7
   Install reclining remote control lever bezel rh (w/o rear no. 2 Seat) (see page se-105)
8. 8
   Install reclining remote control lever bezel lh (w/o rear no. 2 Seat) (see page se-73)
9. 9
   Install rear deck trim cover rh (w/ rear no.

2 Seat) (see page ir-55)

Install rear deck trim cover lh (w/ rear no.

2 Seat) (see page ir-55)

Install rear floor finish plate (see page ir- 55)

Install back door weatherstrip

Install rear floor no. 1 Mat support side plate (see page ir-55)

Install rear floor no. 2 Board

Install rear floor no. 3 Board

Install rear no. 2 Seat assembly rh (w/ rear no. 2 Seat)

1. 1
   Install the rear no. 2 Seat (see page se-121).
2. 2
   Install rear no. 2 Seat assembly lh (w/ rear no. 2 Seat)
3. 3
   Install the rear no. 2 Seat (see page se-121).
4. 4
   Install deck board assembly (w/o rear no. 2 Seat)
5. 5
   Install rear floor no. 1 Board (w/o rear no.

2 Seat)

Install rear floor no. 1 Board (w/o rear no.

2 Seat)

Install package tray trim pocket subassembly (w/o rear no. 2 Seat)

Install lower center pillar garnish rh (see page ir-56)

Install lower center pillar garnish lh (see page ir-56)

Install rear door opening trim weatherstrip rh

Install rear door opening trim weatherstrip lh

Install rear door scuff plate rh (see page ir-57)

Install rear door scuff plate lh (see page ir-57)

Install front door opening trim weatherstrip rh

Install front door opening trim weatherstrip lh

Install cowl side trim board rh (see page ir- 59)

Install cowl side trim board lh (see page ir- 59)

Install front door scuff plate rh (see page ir-59)

Install front door scuff plate lh (see page ir-59)

Install rear console box sub-assembly (see page ip-26)

Install rear console box sub-assembly (see page ip-26)

Install rear console box sub-assembly (see page ip-26)

Install rear console box sub-assembly (see page ip-26)

Install upper rear console panel subassembly (see page ip-27)

Install upper rear console panel subassembly (see page ip-27)

Install switch base (see page ip-27)

Install upper console panel sub-assembly (see page ip-27)

Install no. 2 Console upper panel garnish (see page ip-28)

Install no. 1 Console upper panel garnish (see page ip-28)

Install rear no. 1 Seat assembly lh

1. 1
   Install the rear no. 1 Seat (see page se-64).
2. 2
   Install rear no. 1 Seat assembly rh
3. 3
   Install the rear no. 1 Seat (see page se-97).
4. 4
   Install front seat assembly lh
5. 5
   Install the front seat.
6. 6
   Install front seat assembly rh
7. 7
   Install the front seat.
8. 8
   Connect cable to negative battery terminal
9. 9
   Check srs warning light
10. 10
    Check the srs warning light (see page rs-37).

For manual seat (see page se-22) for power seat (see page se-37). For manual seat (see page se-22) for power seat (see page se-37)