Reassembly

1. 1
   Install front seat wire
2. 2
   Install seat position airbag sensor (see page rs-390)
3. 3
   Install lumbar support adjuster assembly

   

1. 1
   Install the lumbar support adjuster with the 2 screws.
2. 2
   Connect the connector.
3. 3
   Install front seat cushion lower shield lh

   

1. 1
   Attach the hook of the lower shield.
2. 2
   Install the lower shield with the screw.
3. 3
   Install front seat cushion lower shield rh

Use the same procedures described for the lh side.

6. Install reclining adjuster upper inside cover lh

1. 1
   Install the inside cover with the screw.
2. 2
   Install reclining adjuster upper inside cover rh
3. 3
   Install the inside cover with the screw.
4. 4
   Install reclining adjuster lower inside cover lh

   

1. 1
   Attach the claw to install the inside cover.
2. 2
   Install the 2 screws.
3. 3
   Install reclining adjuster lower inside cover rh

   

Use the same procedures described for the lh side.

10. Install front seatback heater (w/ seat heater system)

1. Using a tacker, install the seatback heater to the end of the seat cover with 6 new tack pins.

Do not substitute other metal parts for tack pins.

11. Install front seatback cover

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

1. 1
   Using hog ring pliers, install the seatback cover to the seatback pad with 11 new hog rings.
2. 2
   Install the seatback cover (with pad) to the seat frame (with adjuster).

   

3. W/ front seat side airbag: fully cover the airbag with the 2 seatback cover brackets and install the nut.

• For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
• Make sure that the strap is not twisted after installing the bracket.
• Install the bracket securely.

4. Attach the 4 claws to install the 2 headrest supports.

1. 1
   Attach the hooks.
2. 2
   Using hog ring pliers, install the seatback cover (with pad) with 5 new hog rings.
3. 3
   Install front seatback board subassembly lh

   

1. Push the seatback board in the direction indicated by the arrow in the illustration to attach the 2 claws.

1. 1
   Open the lower part of the seatback board. Then install the seatback board with the 2 screws.
2. 2
   Install front seat cushion heater (w/ seat heater system)

   

1. Using a tacker, install the seat cushion heater to the end of the seat cover with 10 new tack pins.

Do not substitute other metal parts for tack pins.

14. Install front seat cushion cover

1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.

• Be careful not to damage the cover.
• When installing the hog rings, avoid wrinkling the cover.

2. Install the seat cushion cover (with pad) to the seat frame (with adjuster).

1. 1
   Attach the hooks and install the 2 clips.
2. 2
   W/ seat heater system: connect the connector.
3. 3
   Install front power seat switch
4. 4
   Connect the connector.

   

1. 1
   Install the switch with the 3 screws.
2. 2
   Install front seat inner belt assembly lh (see page sb-23)
3. 3
   Install front seat cushion inner shield lh

   

1. 1
   Attach the clip and 3 claws to install the inner shield.
2. 2
   Install the screw.
3. 3
   Install front power seat lumbar switch

   

1. 1
   Install the switch to the cushion shield with the 2 screws.
2. 2
   Install front seat cushion shield lh

   

1. 1
   Install the front no. 1 Seat cushion inner shield to the cushion shield.
2. 2
   Attach the claw to install the front no. 1 Seat cushion inner shield.
3. 3
   Install the screw.
4. 4
   Connect the connector to the front power seat lumbar switch.

   

1. 1
   Attach the 3 claws and install the cushion shield (with front no. 1 Seat cushion inner shield) to the seat frame (with adjuster).
2. 2
   Install the 5 screws.

   

1. 1
   Connect the 2 rubber bands of the front seatback board to the seat frame (with adjuster).
2. 2
   Install slide and vertical power seat switch knob
3. 3
   Install reclining power seat switch knob