Toyota Sienna Quiz
Seat

Reassembly

In this manual: Seat
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
~2min read

1. INSTALL REAR SEAT STAY SUB-ASSEMBLY

  1. Install the seat stay sub-assembly with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

2. INSTALL NO. 2 SEAT CUSHION SPRING ASSEMBLY RH

3. INSTALL LOCUS CABLE RH

  1. Install the locus cable RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

4. INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY RH

INSTALL NO. 2 SEAT CUSHION COVER SUBASSEMBLY RH
  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the seat cushion pad with new hog rings.

NOTICE:

  • Be careful not to damage the cover.
  • When installing the hog rings, take care to prevent wrinkles as much as possible.

5. INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY

  1. Install the rear seat lock release strap assembly with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

6. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO. 2 RH

  1. Install the reclining adjuster release handle No. 2 RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

7. INSTALL RECLINING RELEASE HANDLE SUBASSEMBLY RH

  1. Install the reclining release handle sub-assembly RH with the nut.

    Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf)

8. INSTALL REAR SEAT BACK CONNECTING RH WIRE

  1. Install the rear seat back connecting RH wire.

9. INSTALL NO. 2 SEATBACK COVER RH

INSTALL NO. 2 SEATBACK COVER RH
  1. Using hog ring pliers, install the No. 2 seatback cover RH to the seatback pad with new hog rings.

NOTICE:

  • Be careful not to damage the cover.
  • When installing the hog rings, take care to prevent wrinkles as much as possible.
  1. Install the 2 headrest supports.

10. INSTALL NO. 2 SEATBACK LOCK CONTROL BEZEL

  1. Install the No. 2 seatback lock control bezel with the screw.

11. INSTALL NO. 2 REAR SEAT COVER BEZEL

  1. Install the No. 2 rear seat cover bezel with 3 screws.

12. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY INNER RH

  1. Install the No. 2 rear seat belt assembly inner RH with the bolt.

    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)

13. INSTALL REAR SEATBACK ASSEMBLY RH

  1. Install the rear seatback assembly RH with the 4 bolts.

    Torque: 44 N*m (449 kgf*cm, 32 ft.*lbf)

14. INSTALL LH SEAT REAR SEAT RECLINING COVER

INSTALL LH SEAT REAR SEAT RECLINING COVER
  1. Install the LH seat rear seat reclining cover with 2 screws.

15. INSTALL RH SEAT REAR SEAT RECLINING COVER

INSTALL RH SEAT REAR SEAT RECLINING COVER
  1. Install the RH seat rear seat reclining cover with 2 screws.

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.