Toyota Sienna Quiz
Windshield / windowglass

Removal

In this manual: Windshield / windowglass
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
7steps
~42min
2/5difficulty
Done 0 of 7

1. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

2. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

3. REMOVE FRONT PILLAR GARNISH LH

4. REMOVE FRONT PILLAR GARNISH RH

5. REMOVE VISOR ASSEMBLY LH

6. REMOVE VISOR ASSEMBLY RH

7. REMOVE ASSIST GRIP SUB-ASSEMBLY (2)

8. REMOVE VISOR HOLDER (1)

9. REMOVE ROOF CONSOLE BOX ASSEMBLY

10. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)

11. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

12. REMOVE ROOF HEADLINING ASSEMBLY (4)

13. REMOVE FRONT WIPER ARM HEAD CAP

14. REMOVE FRONT WIPER ARM LH

15. REMOVE FRONT WIPER ARM RH

16. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

17. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

18. REMOVE COWL TOP VENTILATOR LOUVER SUBASSEMBLY

19. REMOVE WINDSHIELD MOULDING OUTER UPPER

REMOVE WINDSHIELD MOULDING OUTER UPPER
  1. Using a knife, cut off the moulding, as shown in the illustration.

NOTICE: Do not damage the vehicle body with the knife.

  • Remove the remaining moulding.

    • HINT: When removing, make a partial a cut, then pull and remove it by hand.
  • w/ Deicer: Disconnect the connector, as shown in the illustration.

    • 20. REMOVE WINDSHIELD GLASS

    REMOVE WINDSHIELD GLASS
    1. Pass a piano wire between the vehicle body and glass from the interior.
      REMOVE WINDSHIELD GLASS
    2. Tie both wire ends to wooden blocks or similar objects.

    HINT: Apply protective tape to the outer surface of the vehicle body to prevent its surface from being scratched.

    NOTICE:

    • When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    • To prevent the safety pad from being scratched when removing the glass, place a plastic sheet between the piano wire and safety pad.
    1. Cut off the adhesive by pulling piano wire around the glass.
    2. Disengage the stoppers.
    3. Using a suction cup, remove the glass.

    NOTICE: Leave as much adhesive on the vehicle body as possible when removing the glass.

    21. CLEAN WINDSHIELD GLASS

    CLEAN WINDSHIELD GLASS
    1. Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.
    2. Clean the outer circumference of the glass with white gasoline.

    NOTICE: Do not touch the glass surface after cleaning it.

    Test yourself

    A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.