Toyota Tacoma Quiz
Exterior

Disassembly

In this manual: Exterior
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
DISASSEMBLY CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.
  • When removing the No. 2 front wheel opening extension pad or No. 1 front wheel opening extension pad or front wheel opening extension pad, heat the front fender wheel opening moulding using a heat light.
  • When removing the No. 3 body outside moulding pad or No. 2 body outside moulding pad or No. 1 body outside moulding pad, heat the quarter panel wheel opening moulding using a heat light.
Heating Temperature

Item

Temperature

Front Fender Wheel Opening Moulding or Quarter Panel Wheel Opening Moulding

20 to 30 °C

NOTICE:

Do not heat the front fender wheel opening moulding or quarter panel wheel opening moulding excessively.

PROCEDURE

1. REMOVE NO. 2 FRONT WHEEL OPENING EXTENSION PAD

(a) Using a heat light, heat the front fender wheel opening moulding.

(b) Remove the No. 2 front wheel opening extension pad.

2. REMOVE NO. 1 FRONT WHEEL OPENING EXTENSION PAD

(a) Using a heat light, heat the front fender wheel opening moulding.

(b) Remove the No. 1 front wheel opening extension pad.

3. REMOVE FRONT WHEEL OPENING EXTENSION PAD

(a) Using a heat light, heat the front fender wheel opening moulding.

(b) Remove the front wheel opening extension pad.

4. REMOVE NO. 3 BODY OUTSIDE MOULDING PAD

(a) Using a heat light, heat the quarter panel wheel opening moulding.

(b) Remove the No. 3 body outside moulding pad.

5. REMOVE NO. 2 BODY OUTSIDE MOULDING PAD

(a) Using a heat light, heat the quarter panel wheel opening moulding.

(b) Remove the No. 2 body outside moulding pad.

6. REMOVE NO. 1 BODY OUTSIDE MOULDING PAD

(a) Using a heat light, heat the quarter panel wheel opening moulding.

(b) Remove the No. 1 body outside moulding pad.

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.