Toyota Tacoma Quiz
2gr-fks Engine Mechanical

Front Crankshaft Oil Seal

In this manual: 2gr-fks Engine Mechanical
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~1min read
1special tools
Components COMPONENTS ILLUSTRATION Installation Installation INSTALLATION PROCEDURE

1. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

(a) Apply MP grease to the lip of a new timing gear case or timing chain case oil seal.

(b) Using SST and a hammer, tap in the timing gear case or timing chain case oil seal until its surface is flush with the timing chain cover edge.

SST: 09226-10010

NOTICE:

  • Keep the lip free from foreign matter.
  • Do not tap the oil seal at an angle.

2. INSTALL CRANKSHAFT PULLEY

3. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/ Oil Cooler)

3. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/ Oil Cooler)

4. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/o Oil Cooler)

4. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY (w/o Oil Cooler)

5. CONNECT NO. 1 WATER BY-PASS PIPE (w/ Oil Cooler)

5. CONNECT NO. 1 WATER BY-PASS PIPE (w/ Oil Cooler)

6. INSTALL RADIATOR ASSEMBLY

6. INSTALL RADIATOR ASSEMBLY

(See page Removal )

Removal REMOVAL PROCEDURE

1. REMOVE RADIATOR ASSEMBLY

(See page 2. DISCONNECT NO. 1 WATER BY-PASS PIPE (w/ Oil Cooler) )

2. DISCONNECT NO. 1 WATER BY-PASS PIPE (w/ Oil Cooler)

3. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY (w/ Oil Cooler)

3. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY (w/ Oil Cooler)

4. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY (w/o Oil Cooler)

4. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY (w/o Oil Cooler)

5. REMOVE CRANKSHAFT PULLEY

5. REMOVE CRANKSHAFT PULLEY

6. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

6. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

(a) Using a screwdriver, pry out the timing gear case or timing chain case oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole or crankshaft.

HINT:

Tape the screwdriver tip before use.

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.