Toyota Tacoma Quiz
2gr-fks Emission Control

Purge Valve

In this manual: 2gr-fks Emission Control
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
010203040502115N·mlb·ft
Tightening torque found on this page
Components COMPONENTS ILLUSTRATION Inspection Inspection INSPECTION PROCEDURE

1. INSPECT PURGE VSV

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*a

Component without harness connected

(Purge VSV)

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20 °C

23 to 26 Ω

If the result is not as specified, replace the purge VSV.

(b) Check the operation of the purge VSV.

(1) Apply battery voltage between the terminals of the purge VSV and check that the following occurs when blowing air into the port (E).

Text in Illustration

*a

Port (E)

*b

Port (F)

*c

Air

OK:

Measurement Condition

Specified Condition

Battery voltage applied between terminals 1 and 2

Air flows from port (F)

Battery voltage not applied between terminals 1 and 2

Air does not flow

If the result is not as specified, replace the purge VSV.
Removal REMOVAL PROCEDURE

1. REMOVE V-BANK COVER SUB-ASSEMBLY

2. REMOVE PURGE VSV 2. REMOVE PURGE VSV

2. REMOVE PURGE VSV

(a) Slide the hose clip and disconnect the purge line hose from the purge VSV.

(b) Disconnect the purge line hose from the purge VSV.

(c) Disconnect the connector from the purge VSV.

(d) Remove the bolt and purge VSV from the intake air surge tank.
Installation INSTALLATION PROCEDURE

1. INSTALL PURGE VSV

(a) Install the purge VSV to the intake air surge tank with the bolt.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(b) Connect the purge line hose to the purge VSV, and slide the hose clip to secure it.

(c) Connect the purge line hose to the purge VSV.

(d) Connect the connector to the purge VSV.

2. INSTALL V-BANK COVER SUB-ASSEMBLY

2gr-fks Engine Control 2gr-fks Engine Control

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.