Toyota Tacoma Quiz
Seat Belt

Rear Center Seat Outer Belt Assembly(for Double Cab)

In this manual: Seat Belt
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~2min read
0204060801004231N·mlb·ft
Tightening torque found on this page
Components COMPONENTS ILLUSTRATION Removal Removal REMOVAL PROCEDURE

1. REMOVE REAR SEATBACK HINGE COVER

2. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

2. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

3. REMOVE SEAT BELT ANCHOR COVER CAP

3. REMOVE SEAT BELT ANCHOR COVER CAP

4. REMOVE REAR SEAT SHOULDER BELT COVER

4. REMOVE REAR SEAT SHOULDER BELT COVER

5. REMOVE CENTER SEATBACK PAD

5. REMOVE CENTER SEATBACK PAD

(a) Remove the center seatback pad.

6. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the rear center seat outer belt assembly and rear seat inner belt assembly.

(b) Insert the belt through the hole into the rear seatback frame.

(c) Remove the bolt.

(d) Disengage the 2 guides to remove the rear center seat outer belt assembly.

Installation INSTALLATION PROCEDURE

1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Before installing the rear center seat outer belt assembly, check the ELR function.

Text in Illustration

*a

Unlock

*b

Lock

*c

45°

(1) When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

NOTICE:

Do not disassemble the retractor.

(b) Engage the 2 guides to install the rear center seat outer belt assembly with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(c) Insert the belt through the hole into the rear seatback frame.

(d) Connect the rear seat inner belt assembly and rear center seat outer belt assembly by installing the floor anchor with the bolt.

Text in Illustration

*a

Protruding Part

*b

40°

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

NOTICE:

  • Make sure that the rear seat inner belt assembly and rear center seat outer belt assembly is oriented in the correct direction when installing.
  • Do not allow the anchor part of the rear seat inner belt assembly and rear center seat outer belt assembly to overlap the protruding part of the floor panel.

2. INSTALL CENTER SEATBACK PAD

(a) Install a new center seatback pad.

3. INSTALL REAR SEAT SHOULDER BELT COVER

4. INSTALL SEAT BELT ANCHOR COVER CAP

4. INSTALL SEAT BELT ANCHOR COVER CAP

5. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

5. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

6. INSTALL REAR SEATBACK HINGE COVER

6. INSTALL REAR SEATBACK HINGE COVER

Rear Seat Inner Belt Assembly(for Access Cab)

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.