DESCRIPTION
The occupant classification system circuit consists of the airbag sensor assembly and the occupant classification system.
If the airbag sensor assembly receives signals from the occupant classification ECU, it determines whether the front passenger airbag, the front seat airbag RH and front seat outer belt should be operated.
DTC B1650 is stored when a malfunction is detected in the occupant classification system circuit.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
B1650 |
Occupant Classification System Malfunction |
When one of following conditions is met:
- No. 2 Floor wire
- Front seat wire RH
- Occupant classification system
- Airbag sensor assembly
|
- No. 2 Floor wire
- Front seat wire RH
- Occupant classification system
- Airbag sensor assembly
|
Comes on |
Not applicable |
WIRING DIAGRAM
NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
PROCEDURE
CHECK DTC (OCCUPANT CLASSIFICATION SYSTEM)
(a) Check for occupant classification system DTCs.
Click here 
OK:
DTCs are not output.
| NG |
 |
GO TO OCCUPANT CLASSIFICATION SYSTEM |
| OK |
 |
|
CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the airbag sensor assembly and occupant classification ECU.
OK:
The connectors are properly connected.
| NG |
 |
CONNECT CONNECTORS PROPERLY |
| OK |
 |
|
CHECK CONNECTORS
(a) Disconnect the connectors from the airbag sensor assembly and occupant classification ECU.
(b) Check that the connectors (on the airbag sensor assembly side and occupant classification ECU side) are not damaged.
OK:
The connectors are not deformed or damaged. |
 |
*1 |
Occupant Classification ECU |
*2 |
Airbag Sensor Assembly |
*3 |
Front Seat Wire RH |
*4 |
No. 2 Floor Wire |
|
|
| NG |
 |
REPLACE FRONT SEAT WIRE RH OR NO. 2 FLOOR WIRE |
| OK |
 |
|
CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT
(a) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds. |
 |
*1 |
Occupant Classification ECU |
*2 |
Airbag Sensor Assembly |
*3 |
Front Seat Wire RH |
*4 |
No. 2 Floor Wire |
*5 |
Service Wire |
*a |
Front view of wire harness connector
(to Occupant Classification ECU) |
*b |
Front view of wire harness connector
(to Airbag Sensor Assembly) |
|
|
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
Y2-8 (FSR+) - Body ground |
Ignition switch ON |
Below 1 V |
Y2-4 (FSR-) - Body ground |
Ignition switch ON |
Below 1 V |
(d) Turn the ignition switch off.
(e) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(f) Using a service wire, connect terminals 32 (FSR+) and 31 (FSR-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Y2-8 (FSR+) - Y2-4 (FSR-) |
Always |
Below 1 Ω |
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
Y2-8 (FSR+) - Y2-4 (FSR-) |
Always |
1 MΩ or higher |
Y2-8 (FSR+) - Body ground |
Always |
1 MΩ or higher |
Y2-4 (FSR-) - Body ground |
Always |
1 MΩ or higher |
| NG |
 |
REPLACE AIRBAG SENSOR ASSEMBLY |
| OK |
 |
|
CHECK NO. 2 FLOOR WIRE
(a) Disconnect the instrument panel wire connector from the engine room main wire. |
 |
*1 |
Occupant Classification ECU |
*2 |
Airbag Sensor Assembly |
*3 |
Front Seat Wire RH |
*4 |
No. 2 Floor Wire |
*5 |
Service Wire |
*a |
Front view of wire harness connector
(to Front Seat Wire RH) |
*b |
Front view of wire harness connector
(to Airbag Sensor Assembly) |
|
|
(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Switch Condition | Specified Condition |
QY1-1 (FSR+) - Body ground |
Ignition switch ON |
Below 1 V |
QY1-4 (FSR-) - Body ground |
Ignition switch ON |
Below 1 V |
(e) Turn the ignition switch off.
(f) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
(g) Using a service wire, connect terminals 32 (FSR+) and 31 (FSR-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
QY1-1 (FSR+) - QY1-4 (FSR-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
QY1-1 (FSR+) - QY1-4 (FSR-) |
Always |
1 MΩ or higher |
QY1-1 (FSR+) - Body ground |
Always |
1 MΩ or higher |
QY1-4 (FSR-) - Body ground |
Always |
1 MΩ or higher |
| OK |
 |
REPLACE FRONT SEAT WIRE RH |
| NG |
 |
REPLACE FLOOR WIRE NO.2 |
|