Toyota Venza Quiz
Axle And Differential

Differential Mount Cushion

In this manual: Axle And Differential
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~3min read
2special tools
Components COMPONENTS ILLUSTRATION
Installation INSTALLATION PROCEDURE

1. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, install a new rear No. 1 differential mount cushion.

Text in Illustration

*1

Protrusion

-

-

SST: 09570-24011

(A):

5.0 to 6.0 mm (0.197 to 0.236 in.)

(B):

+/- 3°

NOTICE:

  • Install the rear No. 1 differential mount cushion so that the protrusion is positioned upward.
  • Install the rear No. 1 differential mount cushion within +/- 3° from the center.
  • Temporarily install the rear No. 1 differential mount cushion to the rear suspension member before installing SST to prevent the rear No. 1 differential mount cushion from being tilted.
  • Apply grease to the threads of the SST bolts before use.
  • Be sure to use SST in the correct combination.
  • Do not set SST in the wrong direction.
  • Make sure that SST contacts the entire rear No. 1 differential mount cushion seating surface.
  • Do not slant the SST bolts.
  • Tighten the 2 SST bolts equally into the 2 rear No. 1 differential mount cushion holes.

2. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, install a new rear No. 2 differential mount cushion.


SST: 09570-24011

(A):

5.0 to 6.0 mm (0.197 to 0.236 in.)

(B):

+/- 3°

NOTICE:

  • Install the rear No. 2 differential mount cushion within +/- 3° from the center.
  • Temporarily install the rear No. 2 differential mount cushion to the rear suspension member before installing SST to prevent the rear No. 2 differential mount cushion from being tilted.
  • Apply grease to the threads of the SST bolts before use.
  • Be sure to use SST in the correct combination.
  • Do not set SST in the wrong direction.
  • Make sure that SST contacts the entire rear No. 2 differential mount cushion seating surface.
  • Do not slant the SST bolts.

3. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

HINT:

Refer to the procedure from Install Rear Differential Carrier Assembly with Differential Support (See page ).


Removal REMOVAL PROCEDURE

1. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

HINT:

Refer to the procedure up to Remove Rear Differential Carrier Assembly with Differential Support (See page ).


2. REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, remove the rear No. 1 differential mount cushion.


SST: 09316-12010

SST: 09570-24011

NOTICE:

  • Do not bring SST into contact with the rear suspension member.
  • Do not slant the SST bolts.
  • Do not set SST in the wrong direction.
  • Tighten the 2 SST bolts equally into the 2 rear No. 1 differential mount cushion holes.

3. REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, remove the rear No. 2 differential mount cushion.


SST: 09316-12010

SST: 09570-24011

NOTICE:

  • Do not bring SST into contact with the rear suspension member.
  • Do not slant the SST bolts.
  • Do not set SST in the wrong direction.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.