Toyota Venza Quiz
1ar-fe Engine Mechanical

Front Crankshaft Oil Seal

In this manual: 1ar-fe Engine Mechanical
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
8special tools
080160240320400260192N·mlb·ft
Tightening torque found on this page
Components COMPONENTS ILLUSTRATION
Removal REMOVAL PROCEDURE

1. REMOVE FRONT WHEEL RH

2. REMOVE NO. 1 ENGINE UNDER COVER

3. SEPARATE FRONT FENDER LINER RH

4. REMOVE FRONT FENDER APRON SEAL RH


5. REMOVE V-RIBBED BELT


6. REMOVE CRANKSHAFT PULLEY

(a) Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

SST: 09213-54015

SST: 09330-00021

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)

(b) Using SST and the pulley bolt, remove the crankshaft pulley.

SST: 09950-50013

09951-05010

09952-05010

09953-05020

09954-05011

HINT:

Apply a lubricant to the threads and end of SST.

7. REMOVE TIMING CHAIN COVER OIL SEAL

(a) Using a screwdriver, pry out the oil seal.

HINT:

Tape the screwdriver tip before use.

NOTICE:

Do not damage the surface of the oil seal press fit hole or the crankshaft.
Installation INSTALLATION PROCEDURE

1. INSTALL TIMING CHAIN COVER OIL SEAL

(a) Apply MP grease to the lip of a new oil seal.

NOTICE:

  • Do not allow foreign matter to contact the lip of the oil seal.
  • Do not allow MP grease to contact the dust seal.

(b) Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

SST: 09223-22010

NOTICE:

  • Keep the lip of the oil seal free from foreign matter.
  • Do not tap in the oil seal at an angle.

2. INSTALL CRANKSHAFT PULLEY

(a) Align the pulley set key with the key groove of the crankshaft pulley.

(b) Using SST, hold the crankshaft pulley and install the pulley bolt.

SST: 09213-54015

SST: 09330-00021

Torque:

260 N·m {2651 kgf·cm, 192 ft·lbf}

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)

3. INSTALL V-RIBBED BELT


4. INSTALL FRONT FENDER APRON SEAL RH


5. INSTALL FRONT FENDER LINER RH

6. INSTALL NO. 1 ENGINE UNDER COVER

7. INSTALL FRONT WHEEL RH

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.