Installation

1. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/o Sliding Roof)

NOTICE:

• If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.
• If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.

(a) Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips. HINT: Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2) or more (when the temperature is 23 °C.)

(b) Press and install the 2 roof drip side finish moulding clips.

(c) Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent). Standard Dimension Item Dimension A 4.4 mm (0.173 in.) B 10.2 mm (0.402 in.) C 2.1 mm (0.0827 in.) D 3.0 mm (0.118 in.) E 3.0 mm (0.118 in.) F 5.7 mm (0.224 in.) G 10.4 mm (0.409 in.)

(d) Install the roof drip center side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 roof drip side finish moulding clips.

HINT:

• Initial hardening time: 20 minutes
• Complete hardening time: 48 hours

2. INSTALL ROOF DRIP CENTER SIDE FINISH MOULDING (w/o Sliding Roof)

(a) Engage the 2 clips and install the roof drip center side finish moulding as shown in the illustration.

3. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP (w/ Sliding Roof)

NOTICE:

• If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.
• If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.

(a) Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips. HINT: Adhesive strength (tensile strength): 13.7 MPa (140 kgf/cm2) or more (when the temperature is 23 °C.)

(b) Press and install the 2 roof drip side finish moulding clips.

(c) Install the clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent). Standard Dimension Item Dimension A 4.9 mm (0.193 in.) B 8.4 mm (0.331 in.) C 2.1 mm (0.0827 in.) D 3.0 mm (0.118 in.) E 3.0 mm (0.118 in.) F 5.6 mm (0.221 in.) G 10.4 mm (0.409 in.)

(d) Install the roof drip center side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 roof drip side finish moulding clips.

HINT:

• Initial hardening time: 20 minutes
• Complete hardening time: 48 hours

4. INSTALL ROOF DRIP CENTER SIDE FINISH MOULDING (w/ Sliding Roof)

(a) Engage the 2 clips and install the roof drip center side finish moulding as shown in the illustration.