Toyota Venza Quiz
Power Distribution

Main Body Ecu

In this manual: Power Distribution
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
Components COMPONENTS ILLUSTRATION
Removal REMOVAL PROCEDURE

1. REMOVE UPPER INSTRUMENT PANEL

HINT:

Refer to the procedure up to Remove Upper Instrument Panel Sub-assembly (See page ).


2. REMOVE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 4 connectors.

(b) Disengage the 2 claws and disconnect the connector <A> as shown in the illustration.

(c) Disconnect the 3 connectors.

(d) Disconnect the 3 connectors as shown in the illustration.

(e) Disconnect the connector <A> as shown in the illustration.

(f) Disconnect the connector.

(g) Disconnect the 2 connectors.

(h) Remove the 3 nuts.

(i) Disengage the 2 claws.

(j) Disconnect the connector <A> as shown in the illustration.

(k) Disconnect the 4 connectors and remove the main body ECU (driver side junction block assembly).

(l) Remove the 5 relays.
Installation INSTALLATION PROCEDURE

1. INSTALL MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

(a) Install the 5 relays.

(b) Connect the 4 connectors.

(c) Connect the connector <A> as shown in the illustration.

NOTICE:

Be sure to engage each connector securely.

(d) Engage the 2 claws.

(e) Install the 3 nuts and install the main body ECU (driver side junction block assembly).

(f) Connect the 2 connectors.

NOTICE:

Be sure to engage the connector securely.

(g) Connect the connector <A> as shown in the illustration.

NOTICE:

Be sure to engage the connector securely.

(h) Connect the connector.

NOTICE:

Be sure to engage each connector securely.

(i) Connect the 3 connectors as shown in the illustration.

NOTICE:

Be sure to engage each connector securely.

(j) Engage the 2 claws to connect the connector <A> as shown in the illustration.

NOTICE:

Be sure to engage the connector securely.

(k) Connect the 3 connectors.

NOTICE:

Be sure to engage each connector securely.

(l) Connect the 4 connectors.

NOTICE:

Be sure to engage each connector securely.

2. INSTALL UPPER INSTRUMENT PANEL

HINT:

Refer to the procedure from Install Upper Instrument Panel Sub-assembly (See page ).

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.