Toyota Venza Quiz
Mirror (ext)

Outer Rear View Mirror Glass

In this manual: Mirror (ext)
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~1min read
Components COMPONENTS ILLUSTRATION
Inspection INSPECTION PROCEDURE

1. INSPECT OUTER MIRROR RH

(a) Check the outer mirror heater operation.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

25 °C

7.6 to 11.4 Ω
Text in Illustration

*a

Component without harness connected

(Outer Mirror RH)

If the result is not as specified, replace the outer mirror RH.

2. INSPECT OUTER MIRROR LH

(a) Check the outer mirror heater operation.

(1) Measure the resistance according the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

25 °C

7.6 to 11.4 Ω
Text in Illustration

*a

Component without harness connected

(Outer Mirror LH)

If the result is not as specified, replace the outer mirror LH.
Removal REMOVAL PROCEDURE

1. REMOVE OUTER MIRROR

(a) Push the lower part of the outer mirror surface and tilt it.

Text in Illustration

*1

Protective Tape

(b) Apply protective tape as shown in the illustration.

(c) Using a clip remover, disengage the 2 claws at the upper part of the outer mirror.

(d) Disengage the 2 claws and disconnect the outer mirror as shown in the illustration.

(e) Disconnect the 2 connectors and remove the outer mirror.
Installation INSTALLATION PROCEDURE

1. INSTALL OUTER MIRROR

(a) Connect the 2 connectors.

(b) Engage the 2 claws on the lower part of the outer mirror to the outer rear view mirror assembly as shown in the illustration.

(c) Engage the 2 claws on the upper part of the outer mirror to the outer rear view mirror assembly.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.