Electrical System

Anti-Theft Alarm System

~5min read
0102030405032N·mlb·ft
Tightening torque found on this page

Overview - Interior Monitoring

Overview - Interior Monitoring, Sedan

Overview - Interior Monitoring, Sedan

1 - Alarm Horn -H12-

  • Removing and installing. Refer to → Chapter "Alarm Horn -H12-, Removing and Installing".

2 - Nut

  • 3 N·m

3 - Bracket

  • For Alarm Horn -H12-

4 - Nut

  • 3 N·m

5 - Left Interior Monitoring Individual Sensor

  • Can only be replaced together with the Anti-Theft Alarm System Sensor -G578-

6 - Anti-Theft Alarm System Sensor -G578-

  • Removing and installing. Refer to → Chapter "Anti-Theft Alarm System Sensor -G578-, Removing and Installing".

7 - Individual Sensor

  • For Anti-Theft Alarm System Sensor -G578-
  • Removing and installing. Refer to → Chapter "Anti-Theft Alarm System Sensor -G578-, Removing and Installing".

8 - Right Interior Monitoring Individual Sensor

  • Can only be changed together with the Anti-Theft Alarm System Sensor -G578-

9 - Mount

  • For the Anti-Theft Alarm System Sensor -G578- and the left and right single sensors

10 - Comfort System Central Control Module -J393-

  • Removing and installing. Refer to → Body Exterior; Rep. Gr.57; Central Locking; Comfort System Central Control ModuleJ393, Removing and Installing.

11 - Antenna Amplifier 2 -R111-

  • With Central Locking and Anti-Theft Alarm System Antenna -R47-
  • Removing and installing. Refer to → Communication; Rep. Gr.91; Antenna Systems; Antenna Amplifier, Removing and Installing.

12 - Alarm System Deactivation Switch -E217-

  • Component location overview. Refer to → Chapter "Overview - Front Door Controls".

Tightening Specification for the Structure-Borne Sound Control Module Bracket

- Tighten the nuts -arrows- to 3 N·m.

A21-10695

Overview - Interior Monitoring, Avant

Overview - Interior Monitoring, Avant

1 - Alarm Horn -H12-

  • Removing and installing. Refer to → Chapter "Alarm Horn -H12-, Removing and Installing".

2 - Nut

  • 3 N·m

3 - Bracket

  • For Alarm Horn -H12-

4 - Nut

  • 3 N·m

5 - Left Interior Monitoring Individual Sensor

  • Can only be replaced together with the Anti-Theft Alarm System Sensor -G578-

6 - Anti-Theft Alarm System Sensor -G578-

  • Removing and installing. Refer to → Chapter "Anti-Theft Alarm System Sensor -G578-, Removing and Installing".

7 - Individual Sensor

  • For Anti-Theft Alarm System Sensor -G578-
  • Removing and installing. Refer to → Chapter "Anti-Theft Alarm System Sensor -G578-, Removing and Installing".

8 - Right Interior Monitoring Individual Sensor

  • Can only be changed together with the Anti-Theft Alarm System Sensor -G578-

9 - Mount

  • For the Anti-Theft Alarm System Sensor -G578- and the left and right single sensors

10 - Comfort System Central Control Module -J393-

  • Removing and installing. Refer to → Body Exterior; Rep. Gr.57; Central Locking; Comfort System Central Control ModuleJ393, Removing and Installing.

11 - Antenna Amplifier 2 -R111-

  • With Central Locking and Anti-Theft Alarm System Antenna -R47-
  • Removing and installing. Refer to → Communication; Rep. Gr.91; Antenna Systems; Antenna Amplifier, Removing and Installing.

12 - Alarm System Deactivation Switch -E217-

  • Component location overview. Refer to → Chapter "Overview - Front Door Controls".

Alarm Horn -H12-, Removing and Installing

Removing

- Remove the plenum chamber cover. Refer to → Body Exterior; Rep. Gr.50; Bulkhead; Plenum Chamber Cover, Removing and Installing.

Vehicles without Structure-Borne Sound Control Module:

- Remove the nut -1-.

- Disconnect the connector -3-.

- Remove the alarm horn -2- upward.

A96-10810

Vehicles with Structure-Borne Sound Control Module:

- Remove the structure borne sound control module. Refer to → Rep. Gr.23; Sensors.

- Remove nuts -arrows- and remove the mount.

- Remove the nut -2-.

- Disconnect the connector.

- Remove the alarm horn -1- upward.

Installing

Install in reverse order of removal.

A21-10695

Anti-Theft Alarm System Sensor -G578-, Removing and Installing

Removing

- Remove the front interior/reading lamp. Refer to → Chapter "Front Interior Lamp/Reading Lamp, Removing and Installing".

- Remove the single sensor -1- from the mount -2-.

- Release the tabs -arrows- and remove the mount -4- and anti-theft alarm system sensor from the interior/reading lamp -3-.

A96-10808

- Free up the wire -5-.

- Press the tabs to the side in direction of -arrows- and remove the anti-theft alarm system sensor -1- from the mount -3-.

- Turn the single sensors -2 and 4- counterclockwise all the way in direction of -arrow A- and remove them from the mount in direction of -arrow B-.

- Remove the anti-theft alarm system sensor.

Installing

Install in reverse order of removal.

A96-10809

Anti-Theft Immobilizer Reader Coil, Removing and Installing

Anti-Theft Immobilizer Reader Coil -D2-, Removing and Installing

Removing

- Remove the Information Electronics Control Module 1 -J794-. Refer to → Communication; Rep. Gr.91; Infotainment System; Information Electronics Control Module 1 J794, Removing and Installing.

- Release the tabs in direction of -arrows- and remove the anti-theft immobilizer reader coil -1- from the mount.

- Disconnect the connector -2-.

Installing

Install in reverse order of removal.

A94-11104

Anti-Theft Immobilizer Reader Coil -D2-, Removing and Installing

Removing

- Remove the anti-theft immobilizer reading coil. Refer to → Chapter "Anti-Theft Immobilizer Reader Coil -D2-, Removing and Installing".

- Remove the driver side instrument panel cover. Refer to → Body Interior; Rep. Gr.68; Storage Compartments and Covers; Driver Side Instrument Panel Cover, Removing and Installing.

- Remove the bolts -arrows-.

- Remove the mount -2- from the instrument panel -1- downward toward the driver footwell.

Installing

Install in reverse order of removal.

A94-11096