Body

Backrest Cover, Removing and Installing

~4min read

Backrest Cover, Removing and Installing, Standard Seat/Sport Seat/Super Sport Seat

Special tools and workshop equipment required

  • Safety Glove

Removing

WARNING

Danger of being injured by burrs on the backrest cover.

Wear protective gloves.

- Reach behind the backrest cover -1- and pull the cover off the backrest frame to the right as illustrated.

Note

If difficult loosen the hook with Pry Lever -80-200-.

- Repeat the procedure on the opposite side.

- Continue to remove the backrest cover and roll it up until the upper retaining hooks detach from the backrest frame.

- Remove the backrest cover from the backrest -2- upward.

A72-10813

Installing

Install in reverse order of removal. Note the following:

- Insert the backrest cover with the upper hooks -2- into the backrest frame -1-.

- Tilt the backrest cover down and engage the side retaining tabs -3 and 5- and the lower hooks -4-.

- Make sure the tabs on the side fit correctly into the backrest frame and the lower hooks are bent correctly over the backrest frame.

A72-11059

- Push forcefully on backrest cover on the areas marked with the -arrows- until the tabs and hooks click into place.

- Check if the backrest cover is correctly latched.

  • It must not be possible to move the backrest cover at the bottom.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Front Backrest, Standard Seat/Sport Seat".

A72-11060

Backrest Cover, Removing and Installing, Multi-contour Seat

Special tools and workshop equipment required

  • Pry Lever -80-200-
  • Omega Clip Tool -T40280-

Removing

- Move the front seat all the way forward/up.

Note

The clips -1 and 2- together with hooks on the backrest frame can only be detached up to the first catch.

- Release the clips -1 and 2- up to the first retainer -A arrows- using the Pry Lever -80-200-.

- To disengage the clips -1- with the hooks, move the backrest cover -3- in direction of -arrow C-. The clips will slide out of the guide on the backrest cover.

- Then, to disengage the clips -2- with the hooks, move the backrest cover in direction of -arrow B-. The clips will slide out of the guide on the backrest cover.

A72-11113

- Pull the backrest cover -1- in the upper section as far as possible toward the rear from the backrest -arrow-.

- Press down and remove the backrest cover hooks -2- with a large flat blade screwdriver from the backrest frame.

Note

Use a flashlight and mirror if necessary.

A72-11586

- Detach left and right rubber strap -1- at the bottom of the seat pan.

- Pull off backrest cover in upward direction.

Installing

Install in reverse order of removal. Note the following:

- Install backrest cover with catches at the bottom of the backrest frame.

- Insert the clips together with hooks into the guides on the backrest cover.

- Forcefully press backrest cover in the direction of the backrest until the clips engage audibly.

- Check if the backrest cover is correctly latched.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Front Backrest, Multi-contour Seat".

A72-11058

Backrest Cover, Removing and Installing, Market-Specific

Special tools and workshop equipment required

  • Trim Removal Wedge -3409-

Removing

- Vehicles with rear seat entertainment: remove the mount for the rear seat entertainment. Refer to → Chapter "Rear Seat Entertainment Mount/Bracket, Removing and Installing, Market-Specific".

- Unclip the trim -1- using the Trim Removal Wedge -3409- in direction of -arrows- and remove.

A72-11193

- Detach left and right rubber strap -1- at the bottom of the seat pan.

- Remove the bolts -2-.

- Pull off backrest cover in upward direction.

A72-11120

Backrest Cover Bracket

- Remove bolts -arrows- and backrest cover bracket -1-.

Installing

Install in reverse order of removal. Note the following:

- Forcefully press backrest cover in the direction of the backrest until the retaining clips engage audibly.

- Check if the backrest cover is correctly latched.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Front Backrest, Market-Specific".

A72-11194