Body

Multi-contour Seat Valve Block, Removing and Installing

~4min read

Massage Mat Valve Block, Removing and Installing, through 08/2012

Special tools and workshop equipment required

  • Hose Cutting Pliers -VAS6228-

Removing

- Remove the backrest cover. Refer to → Chapter "Backrest Cover, Removing and Installing, Multi-contour Seat".

- Disconnect the connector -3-.

- Push massage mat valve block -4- up slightly to detach it at the module carrier in direction of -arrow A-.

- Carefully release locking mechanism in direction of -arrow B-, disconnect pneumatic lines -1 and 2-.

A72-11170

- Disconnect pneumatic lines to the massage mat air cushions at the following points (refer to → Chapter "Pneumatic Lines, Disconnecting and Connecting"):

  • a - 40 mm

Installing

Install in reverse order of removal. Note the following:

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Pneumatic System, Massage Mat".

A72-11251

Massage Mat Valve Block, Removing and Installing, from 09/2012

Removing

- Remove the backrest cover. Refer to → Chapter "Backrest Cover, Removing and Installing, Multi-contour Seat".

Note

If a repair is required, the pneumatic line from the compressor is not disconnected at the connection, but is disconnected by the described procedure. Refer to → Chapter "Pneumatic Lines, Disconnecting and Connecting".

Driver Side

- Disconnect the pneumatic line -1- from the compressor at the following locations:

  • a - 30 mm
A72-11737

Front Passenger Side

- Disconnect the pneumatic line -1- from the compressor at the following locations:

  • a - 315 mm
A72-11743

Continued for Both Sides

- Disconnect the connector -6-.

- Before disconnecting, mark the pneumatic line assignments to the connections at the valve block using a waterproof permanent marker.

- Disconnect the pneumatic lines -1 through 5- from all of the massage mat air cushions.

A72-11736

- To do this, press the release ring -2- in the direction of the valve block -1--arrow A- and at the same time pull out the pneumatic line -3- in direction of -arrow B-.

A72-11630

- Pull the rubber buffer lengthwise in direction of -arrow A-.

- Remove the valve block from the rubber buffer in direction of -arrow B- simultaneously.

Installing

Install in reverse order of removal. Note the following:

- Connect the pneumatic lines and give them a push again and then a final tug to see whether the coupling is locked in correctly.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Pneumatic System, Massage Mat".

A72-11631

Valve Block for Air Cushion for Lumbar Support, Seat and Backrest Bolster Adjuster Assembly, Removing and Installing, from 09/2012

Special tools and workshop equipment required

  • Hose Cutting Pliers -VAS6228-

Removing

- Remove the backrest cover. Refer to → Chapter "Backrest Cover, Removing and Installing, Multi-contour Seat".

Note

If a repair is required, the pneumatic line from the compressor is not disconnected at the connection, but is disconnected by the described procedure. Refer to → Chapter "Pneumatic Lines, Disconnecting and Connecting".

- Disconnect the pneumatic line -1- to the Valve Block 1 in Driver Seat -N475-/Valve Block 1 in Front Passenger Seat -N477- at the following position:

  • a - 30 mm
A72-11791

- Disconnect the connector -8-.

- Before disconnecting, mark the pneumatic line assignments to the connections at the valve block using a waterproof permanent marker.

- Disconnect the pneumatic lines -1 through 7- from the valve block -A-.

A72-11793

- To do this, press the release mechanism -2--arrow- and simultaneously remove the pneumatic line -1-.

A72-11787

- Pull the rubber buffer lengthwise -arrow A-.

- Remove the valve block from the rubber buffer -arrow B- simultaneously.

Installing

Install in reverse order of removal. Note the following:

- Connect the pneumatic line. Refer to → Chapter "Pneumatic Lines, Disconnecting and Connecting".

- Connect the pneumatic lines and give them a push again and then a final tug to see whether the coupling is locked in correctly.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Pneumatic System, Backrest".

A72-11631