Electrical System

Headlamp Washer System

~3min read
010203040502.52N·mlb·ft
Tightening torque found on this page

Overview - Headlamp Washer System

Overview - Headlamp Washer System

1 - Spray Nozzle for Night Vision System Camera -R212-

  • Removing and installing. Refer to → Chapter "Night Vision System Camera -R212- Spray Nozzle, Removing and Installing".

2 - Screw

  • 2,5 N·m
  • Quantity: 2

3 - Mount

  • For Night Vision System Camera -R212-

4 - Washer Fluid Hose

  • To the spray nozzles

5 - Headlamp Washer Pump -V11-

  • Removing and installing. Refer to → Chapter "Headlamp Washer Pump -V11-, Removing and Installing".

6 - Grommet

  • For Headlamp Washer Pump -V11-

7 - Windshield Washer Fluid Reservoir

8 - Screw

  • 2,5 N·m
  • Quantity: 2

9 - Mount

  • For nozzle
  • Removing and installing. Refer to → Chapter "Headlamp Washer System Spray Nozzle Mount, Removing and installing".

10 - Washer Fluid Hose

  • For the spray nozzle and infrared camera

11 - Spray Nozzle

  • Removing and installing. Refer to → Chapter "Headlamp Washer System Spray Nozzle, Removing and Installing".

12 - O-Ring

  • Replacing

Windshield Washer Fluid Reservoir, Removing and Installing

Note

The shared windshield and headlamp washer system washer fluid reservoir is located in the left front wheel housing.

- Washer fluid reservoir, removing and installing. Refer to → Chapter "Windshield Washer Fluid Reservoir, Removing and Installing".

Headlamp Washer Pump -V11-, Removing and Installing

Removing

- Remove the washer fluid reservoir. Refer to → Chapter "Windshield Washer Fluid Reservoir, Removing and Installing".

- Remove the Headlamp Washer Pump -V11--item 2- upward out of the washer fluid reservoir -3-.

Installing

Install in reverse order of removal. Note the following:

- Check the sealing grommet -1- for damage.

A92-10238

Spray Nozzles, Removing and Installing

Headlamp Washer System Spray Nozzle, Removing and Installing

Removing

- Pull the spray nozzle telescope -2- all the way out of the bumper cover.

  • Hold the telescope in the pulled-out position.

- Open the side retainers in direction of -arrows- and remove the spray nozzle -1- from the telescope.

- Let the telescope go back into the mount slowly.

- Remove the cover if the spray nozzle is being replaced. Refer to → Body Exterior; Rep. Gr.63; Front Bumper; Attachments, Removing and Installing.

Installing

Install in reverse order of removal. Note the following:

- Replace the O-ring -3- if the same spray nozzle is being installed again.

A92-10252

Headlamp Washer System Spray Nozzle Mount, Removing and installing

Removing

- Remove the headlamp washer system spray nozzle. Refer to → Chapter "Headlamp Washer System Spray Nozzle, Removing and Installing".

- Remove the front bumper cover. Refer to → Body Exterior; Rep. Gr.63; Front Bumper; Bumper Cover, Removing and Installing.

- Open the clip in direction of -arrow- and remove the windshield washer fluid hose -3- from the mount.

Note

Depending on the version, release buttons might be installed on the washer fluid hose connecting piece.

- Remove the screws -1 and 4- and the mount -2-.

Installing

Install in reverse order of removal.

A92-10241

Night Vision System Camera -R212- Spray Nozzle, Removing and Installing

Removing

- Remove the Night Vision System Camera -R212- mount. Refer to → Body Exterior; Rep. Gr.63; Front Bumper; Attachments, Removing and Installing.

- Remove the bolts -arrows-.

- Remove the spray nozzle -1- from the mount -2-.

Installing

Install in reverse order of removal. Note the following:

- If the mount is removed, the Night Vision System Camera -R212- must be recalibrated. Refer to → Suspension, Wheels, Steering; Rep. Gr.44; Infrared System; Infrared System, Calibrating.

A92-10239

Spray Nozzles, Adjusting

Note

The nozzles are already adjusted by the manufacturer and must not be adjusted after installation.

Special Tools

Special tools and workshop equipment required

  • Puller - Wiper Arm Kit -T10369-
W00-10632