Chassis

Overview - Rear Axle, Overview - Subframe

~4min read
0408012016020011585N·mlb·ft
Tightening torque found on this page

Overview - Rear Axle

Part I

Overview - Rear Axle

I - → Chapter "Overview - Subframe, Vehicles with FWD"

II - → Chapter "Overview - Subframe, Vehicles with AWD"

III - → Chapter "Overview - Stabilizer Bar"

IV - → Chapter "Overview - Transverse Link"

V - → Chapter "Overview - Wheel Bearing, Vehicles with FWD"

VI - → Chapter "Overview - Wheel Bearing Housing, Vehicles with AWD"

Part II

Overview - Rear Axle

VII - → Chapter "Overview - Suspension Strut, Shock Absorber and Spring, Coil Spring"

VIII - → Chapter "Overview - Suspension Strut, Shock Absorber and Spring, Air Spring"

IX - → Chapter "Overview - Suspension Strut, Shock Absorber and Spring, Shock Absorber"

X - → Chapter "Overview - Drive Axle"

Overview - Subframe

Overview - Subframe, Vehicles with FWD

Overview - Subframe, Vehicles with FWD

1 - Bolt

  • 115 N·m +90º turn
  • Always replace if removed

2 - Front Bonded Rubber Bushing

  • for the subframe mounting
  • There are different versions. Refer to → Fig. "Front and Rear Bonded Rubber Bushings". For the correct allocation. Refer to the Parts Catalog.
  • Oil on the hydraulic bonded rubber bushing is a sign of wear.
  • Replacing. Refer to → Chapter "Subframe Front Bearing, Replacing, Vehicles with FWD".
  • Replace on both sides.

3 - Subframe

  • Subframe with attachments, removing and installing. Refer to → Chapter "Subframe, Removing and Installing, FWD Vehicles".
  • Subframe, securing. Refer to → Chapter "Subframe, Securing, FWD".

Note

An AWD subframe is installed for hybrid vehicles. For the correct allocation. Refer to the Parts Catalog. Performing repairs on the subframe is not affected.

4 - Rear Bonded Rubber Bushing

  • For the subframe mounting
  • There are different versions. Refer to → Fig. "Front and Rear Bonded Rubber Bushings". For the correct allocation. Refer to the Parts Catalog.
  • Oil on the hydraulic bonded rubber bushing is a sign of wear.
  • Replacing. Refer to → Chapter "Subframe Rear Bearing, Replacing, Vehicles with FWD".
  • Replace on both sides.

5 - Bolt

  • 115 N·m +90º turn
  • Always replace if removed

6 - Rear Stone Chip Protection

  • Depending on the date of manufacture

7 - Clip

  • Depending on the date of manufacture

8 - Front Stone Chip Protection

  • Depending on the date of manufacture

Front and Rear Bonded Rubber Bushings

A - Hydraulic bonded rubber bushing

B - Conventional bonded rubber bushing

A42-10489

Diagonal Brace - Tightening Specification

Note

Replace the bolts that were tightened with an additional turn.

- Tighten the bolts -1 through 4- to 50 N·m +90º turn.

A42-10486

Overview - Subframe, Vehicles with AWD

Overview - Subframe, Vehicles with AWD

1 - Clip

  • Depending on the date of manufacture

2 - Center Stone Chip Protection

  • Depending on the date of manufacture

3 - Bolt

  • 115 N·m + 90º turn
  • Always replace if removed

4 - Bolt

  • Tightening specification. Refer to → Rear Final Drive 0BC, 0BD, 0BE, 0BF; Rep. Gr.39.

5 - Subframe

  • Subframe with attachments, removing and installing. Refer to → Chapter "Subframe, Removing and Installing, AWD Vehicles".
  • Subframe, securing. Refer to → Chapter "Subframe, Securing, Vehicles with AWD".

6 - Front Bonded Rubber Bushing

  • For the rear final drive mount
  • Replacing. Refer to → Chapter "Rear Final Drive Front Bearing, Replacing, AWD Vehicles".

7 - Rear Final Drive

  • Removing and installing. Refer to → Rear Final Drive 0BC, 0BD, 0BE, 0BF; Rep. Gr.39.

8 - Rear Bonded Rubber Bushing

  • For the rear final drive mount
  • Replacing. Refer to → Chapter "Rear Final Drive Rear Bearing, Replacing, AWD Vehicles".

9 - Bolt

  • Tightening specification. Refer to → Rear Final Drive 0BC, 0BD, 0BE, 0BF; Rep. Gr.39.

10 - Rear Bonded Rubber Bushing

  • For the subframe mounting
  • There are different versions. Refer to → Fig. "Front and Rear Bonded Rubber Bushings". For the correct allocation. Refer to the Parts Catalog.
  • Oil on the hydraulic bonded rubber bushing is a sign of wear.
  • Replacing. Refer to → Chapter "Subframe Rear Bearing, Replacing, Vehicles with AWD".
  • Always replace on both sides.

11 - Bolt

  • 115 N·m + 90º turn
  • Always replace if removed

12 - Front Bonded Rubber Bushing

  • For The Subframe Mounting
  • There are different versions. Refer to → Fig. "Front and Rear Bonded Rubber Bushings". For the correct allocation. Refer to the Parts Catalog.
  • Oil on the hydraulic bonded rubber bushing is a sign of wear.
  • Replacing. Refer to → Chapter "Subframe Front Bearing, Replacing, Vehicles with AWD".
  • Always replace on both sides.

13 - Left Stone Chip Protection

  • Depending on the date of manufacture

14 - Clip

  • Depending on the date of manufacture

15 - Left Front Stone Chip Protection

  • Depending on the date of manufacture

Front and Rear Bonded Rubber Bushings

A - Hydraulic bonded rubber bushing

B - Conventional bonded rubber bushing

A42-10489