Chassis

Overview - Suspension Strut, Shock Absorber and Spring

~4min read
050100150200250150111N·mlb·ft
Tightening torque found on this page

Overview - Suspension Strut, Shock Absorber and Spring, Coil Spring

Overview - Suspension Strut, Shock Absorber and Spring, Coil Spring

1 - Wheel Bearing Housing

2 - Stone Chip Protection

3 - Lower Spring Plate

  • Note the installed position. Refer to → Fig. "Lower Spring Plate Installed Position".

4 - Coil Spring

  • Note the installed position. Refer to → Fig. "Coil Spring Installed Position".

5 - Spacer Piece

  • Not installed on all vehicles. For the correct allocation. Refer to the Parts Catalog.

6 - Upper Spring Plate

  • Vehicles with an upper eccentric spring plate. Refer to → Fig. "Upper Eccentric Spring Plate Installed Position"; for the correct allocation. Refer to the Parts Catalog.

Lower Spring Plate Installed Position

  • The centering pin -3- on the lower spring plate must fit into the hole -2- in the stone chip protection and into the hole -1- in the wheel bearing housing.
A42-10487

Coil Spring Installed Position

  • Lower color marking -arrow-.
  • Turn the end of the spring all the way to the lower spring plate.
A42-10493

Upper Eccentric Spring Plate Installed Position

  • The -arrow- indicates direction of travel.
  • The centering pin -1- fit into the longitudinal member -2-.
A42-10475

Overview - Suspension Strut, Shock Absorber and Spring, Air Spring

1 - Spring Washer

2 - Wheel Bearing Housing

3 - Stone Chip Protection

4 - Air Spring

  • Removing and installing. Refer to → Chapter "Spring, Removing and Installing, Air Spring".
  • Note installed position. Refer to → Fig. "Air Spring Installed Position".

5 - Air line

  • Tightening specification for the connector -Item 3-

Air Spring Installed Position

  • The positioning pin -3- on the air spring must fit into the hole -5- in the stone chip protection and into the hole -4- in the wheel bearing housing.
  • The hooks -2- must lock onto the lower wheel bearing housing.
  • The spring washer -1- must be pushed on parallel up to the base of the air spring.
  • The positioning pin -6- on the air spring must be installed correctly inside the body.
A42-10507

Overview - Suspension Strut, Shock Absorber and Spring, Shock Absorber

Conventional Shock Absorber

Conventional Shock Absorber

1 - Stone Chip Protection

2 - Bolt

  • 150 N·m +180º turn
  • Always replace if removed
  • Must be tightened in the curb weight position. Refer to → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".

3 - Shock Absorber

  • Because of different shock absorber valve systems, only install new shock absorbers from the same manufacturer on both axles.
  • Removing and Installing. Refer to → Chapter "Shock Absorber, Removing and Installing".
  • Servicing. Refer to → Chapter "Shock Absorber, Servicing, Standard Shock Absorber/with DRC System".

4 - Protective Cap

5 - Nut

  • 35 N·m
  • Always replace if removed

6 - Upper Shock Absorber Mount

7 - Bolt

  • 50 N·m +90º turn
  • Always replace if removed

8 - Stop Buffer

9 - Protective Sleeve

10 - Washer

  • Serves as corrosion protection
  • Always use

Shock Absorber with Electronic Damping

Shock Absorber with Electronic Damping

1 - Stone Chip Protection

2 - Bolt

  • 150 N·m +180º turn
  • Always replace if removed
  • Must be tightened in the curb weight position. Refer to → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".

3 - Shock Absorber

  • Removing and installing. Refer to → Chapter "Shock Absorber, Removing and Installing".
  • Servicing. Refer to → Chapter "Shock Absorber, Servicing, Standard Shock Absorber/with DRC System".

4 - Cable

5 - Protective Cap

6 - Seal

  • For the connector

7 - Connector Housing

  • Do not bend or twist the electric wire when connecting the connector

8 - Protective Cap

9 - Nut

  • 50 N·m
  • Always replace if removed

10 - Upper Shock Absorber Mount

11 - Bolt

  • 50 N·m +90º turn
  • Always replace if removed

12 - Stop Buffer

13 - Protective Sleeve

14 - Washer

  • Serves as corrosion protection
  • Always use

Shock Absorber with Dynamic Ride Control (DRC) System

Shock Absorber with Dynamic Ride Control (DRC) System

1 - Stop Buffer

2 - Protective Sleeve

3 - Shock Absorber Mount

4 - Nut

  • 35 N·m
  • Always replace if removed

5 - Protective Cap

6 - Bolt

  • 50 N·m +90º turn
  • Always replace if removed

7 - Protective Sleeve

8 - Suction/Fill Valve with Hose Line

  • Make sure not under tension when installing

9 - Nut

  • 9 N·m

10 - Clip

11 - Bolt

  • 14 N·m
  • Always replace if removed

12 - Shock Absorber

  • For the Dynamic Ride Control (DRC) system
  • Removing and installing. Refer to → Chapter "Shock Absorber, Removing and Installing".
  • Servicing. Refer to → Chapter "Shock Absorber, Servicing, Standard Shock Absorber/with DRC System".

13 - Stone Chip Protection

14 - Bolt

  • 150 N·m +180º turn
  • Always replace if removed
  • Must be tightened in the curb weight position. Refer to → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".