Chassis

Overview - Suspension Strut and Upper Control Arm

~3min read
010203040503022N·mlb·ft
Tightening torque found on this page
Overview - Suspension Strut and Upper Control Arm

1 - Suspension Strut Dome

2 - Nut

  • 30 N·m
  • Loosen and tighten diagonally
  • Always replace if removed

3 - Bolt

  • 20 N·m

4 - Tower Brace

  • Removing and installing. Refer to → Chapter "Tower Brace, Removing and Installing".

5 - Bolt

  • 20 N·m

6 - Bolt

  • 50 N·m +90º turn
  • Always replace if removed
  • Must be tightened in the control position. Refer to → Chapter "Wheel Bearing in Control Position, Lifting Vehicles with Air Suspension" or → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".

7 - Upper Rear Control Arm

  • Removing and installing. Refer to → Chapter "Upper Control Arm, Removing and Installing".
  • For replacing the bonded rubber bushing for upper rear control arm. Refer to → Chapter "Upper Control Arm Bearing, Replacing".

8 - Bolt

  • Always replace if removed

9 - Washer

10 - Wheel Bearing Housing

11 - Nut

  • 40 N·m
  • Always replace if removed

12 - Coil Spring Shock Absorber

  • Removing and installing. Refer to → Chapter "Suspension Strut, Removing and Installing, Coil Spring Shock Absorber".
  • Servicing. Refer to → Chapter "Suspension Strut, Servicing, Coil Spring Shock Absorber".

13 - Upper Front Control Arm

  • Removing and installing. Refer to → Chapter "Upper Control Arm, Removing and Installing".
  • For replacing the bonded rubber bushing for upper front control arm. Refer to → Chapter "Upper Control Arm Bearing, Replacing".

14 - Bolt

  • 50 N·m +90º turn
  • Always replace if removed
  • Must be tightened in the control position. Refer to → Chapter "Wheel Bearing in Control Position, Lifting Vehicles with Air Suspension" or → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".

15 - Bolt

  • Always replace if removed

16 - Control Arm

17 - Nut

  • 90 N·m +90º turn
  • Always replace if removed
  • Must be tightened in the control position. Refer to → Chapter "Wheel Bearing in Control Position, Lifting Vehicles with Air Suspension"

18 - Shock Absorber Fork

  • Removing and installing. Refer to → Chapter "Shock Absorber Fork, Removing and Installing".

19 - Bolt

  • 40 N·m +180º turn
  • Always replace if removed

20 - Coupling Rod

21 - Bolt

  • 40 N·m +90º turn
  • Always replace if removed
  • Must be tightened in the control position. Refer to → Chapter "Wheel Bearing in Control Position, Lifting Vehicles with Air Suspension" or → Chapter "Wheel Bearing in Curb Weight, Lifting Vehicles with Coil Spring".

22 - Nut

  • Always replace if removed

23 - Air Spring Shock Absorber

  • Removing and installing. Refer to → Chapter "Suspension Strut, Removing and Installing, Air Spring Damper".
  • Servicing. Refer to → Chapter "Suspension Strut, Servicing, Air Spring Damper".
  • There are different versions of the suspension. Refer to → Chapter "Production Control Number (PR number) Explanation".

24 - Connecting Piece for the Air Line and the Residual Pressure Retaining Valve

  • Tightening specification: -Item 5-
  • Only remove if vehicle is raised and air spring damper is unloaded (otherwise, there is a risk of injury from lowering vehicle)
  • If there are leaks. Refer to → Chapter "Air Line, Servicing" or → Chapter "Air Line, Servicing".
  • Clean connections before loosening
  • Air escapes when connections are unscrewed
  • Protect threaded connection from dirt
  • Do not loosen the residual pressure retaining valve.