Transmission

Transmission Control

~7min read

Overview - Transmission Control Module

Diagnostic Connection

  • Component location: The diagnostic connection for the Vehicle Diagnostic Tester in inside the footwell on the driver side.
  • Before servicing the transmission, determine as best as possible the cause of the fault using the Vehicle Diagnostic Tester in Guided Fault Finding, Vehicle Self-Diagnosis and Test Instruments.
N90-10017

S tronic Transmission Mechatronic -J743-, valves, sensor and transmission input RPM sensor

  • Component location: The S tronic Transmission Mechatronic -J743- is attached to the transmission housing at the bottom and covered by the transmission fluid pan.

Note

  • The Mechatronic unit incorporates the hydraulic control, the transmission control module, the multifunction transmission range switch and the sensors and actuators as a complete synchronized unit.
  • OBD checks all the components named.
A34-10312

Gear selector, mechatronic temperature sensor in the overview

1 - Circuit Board 1

2 - Gear selector module

3 - Gear Position Distance Sensor 1 -G487- for gear position 2-R

4 - Gear Position Distance Sensor 2 -G488- for gear position 1-3

5 - Gear Position Distance Sensor 3 -G489- for gear position 7-5

6 - Gear Position Distance Sensor 4 -G490- for gear position 4-6

7 - Clutch Oil Temperature Sensor -G509-

8 - Transmission Input Speed Sensor 3 -G641- for the clutch input speed sensor

9 - Circuit Board 2

10 - Electro-hydraulic control module

The Circuit Board 1 and Circuit Board 2 can be individually removed and installed, description: → S tronic Transmission Internal Components; Rep. Gr.34; Mechatronic.

A34-10637

Mechatronic connectors and sensor module

Mechatronic connectors:

1 - Circuit board connector 1 on the transmission control module

2 - Circuit board connector 2 on the transmission control module

3 - Circuit Board 2

4 - Sensor Module connector at the wiring harness

5 - Drive Position Sensor -G676-

6 - Circuit board 3 in the sensor module

7 - Transmission Input Speed Sensor 1 -G632-

8 - Transmission Input Speed Sensor 2 -G612-

9 - Wiring harness with wiring channel

10 - Transmission control module to vehicle wiring harness

11 - Transmission control module at the sensor module

12 - Transmission control module

The components -4 through 8- are marked as sensor module.

A34-10657

Sensor Module, with integrated transmitters and sensors Transmission Input Speed Sensor 2 -G612-,Transmission Input Speed Sensor 1 -G632-, Drive Position Sensor -G676- and circuit board 3

The Sensor Module-2- is installed in the transmission intermediate housing.

The following components are integrated on the sensor module:

  • Drive Position Sensor -G676-
  • Transmission Input Speed Sensor 1 -G632-
  • Transmission Input Speed Sensor 2 -G612-
  • Circuit board 3

- Sensor Module Removing and Installing, refer to → S tronic Transmission Internal Components; Rep. Gr.34; Transmission, Disassembling and Assembling; Overview - Transmission.

A34-11026

Selector Lever Sensor System Control Module -J587-

  • Component location: The Selector Lever Sensor System Control Module -J587--2- is clipped to the gearshift mechanism function unit -arrows-.
A37-11138

Shift Lock Solenoid -N110-

  • Component location: The Shift Lock Solenoid -N110--1- is clipped to the selector mechanism.
A37-10413

Transmission Park Selector Switch -F305-

  • Component location: The Transmission Park Selector Switch -F305-, which consists of two reed contacts -1- and -2-, is installed on the circuit board -B- on the Shift Lock Solenoid -N110--item A-.

Note

The Transmission Park Selector Switch -F305- can only be replaced together with the Shift Lock Solenoid -N110-.

A37-10411

Transmission Fluid Temperature Sensor 2 -G754-

The 7-speed S tronic transmission 0B5 (S tronic) has an additional Transmission Fluid Temperature Sensor 2 -G754- to monitor the transmission fluid temperature of the wheel set on certain engine versions.

  • Installed location: Depending on the date of manufacture, there are 2 different versions and component locations, either on the side or in place of the transmission fluid drain plug (Manual Transmission Fluid), refer to → S tronic Transmission Internal Components; Rep. Gr.34; Automatic Transmission Fluid.
A34-10870

Transmission Fluid Cooling Valve -N509-

Component location: Depending on the engine types installed at the subframe or at the transmission housing. Removing and installing the Transmission Fluid Cooling Valve -N509-, refer to → Rep. Gr.19; Coolant Pump/Thermostat; Coolant Valve, Removing and Installing.

A19-11244

Transmission Range Display -Y6-

  • Installed location: the Transmission Range Display -Y6--arrow- is integrated inside the instrument cluster.

Note

Replace the instrument cluster if one of the transmission range displays is faulty, refer to → Electrical Equipment; Rep. Gr.90; Instrument Cluster; Overview - Instrument Cluster.

A34-10696

Selector Lever Transmission Range Position Display Unit -Y26-

  • Component location: The Selector Lever Transmission Range Position Display Unit -Y26--item 1- is clipped inside the Multimedia System Control Head -E380-.

Removing and Installing, refer to → Electrical Equipment; Rep. Gr.96; Lamps; Selector Lever Transmission Range Position Display Unit Y26, Removing and Installing.

A34-10645

Kick Down Switch -F8-

A programmed value from the Accelerator Pedal Position Sensor -G79- and Accelerator Pedal Position Sensor 2 -G185- (integrated in accelerator pedal module) are saved in the engine control module as a kick-down signal.

  • Component location: The accelerator pedal position sensors are integrated inside the accelerator pedal module -arrow-.

Note

The accelerator pedal module must be replaced if the accelerator pedal position sensor is faulty, for the removal and Installation, refer to → Fuel Supply System; Rep. Gr.20; Accelerator Pedal Mechanism; Accelerator Pedal Position Sensors G79 / G185 , Removing and Installing.

A24-0204

Transmission Guided Functions

Special tools and workshop equipment required

  • Vehicle Diagnostic Tester

Procedure:

  • Vehicle Diagnostic Tester is connected.

- Perform "Guided Function" in Guided Functions, directory 02 - transmission electronics, functions on the Vehicle Diagnostic Tester.

Conditions:

  • Follow the instructions on the Vehicle Diagnostic Tester exactly so that "Guided Functions" can be performed successfully.

Perform "Guided Functions" with a Vehicle Diagnostic Tester after performing the following:

1 - Replacing the selector mechanism function unit: 02 - basic setting (Repair Group 34).

2 - Working on the selector lever cable, adjusting the selector lever cable: 02 - basic setting (Repair Group 34).

3 - Replacing the S tronic Transmission Mechatronic -J743- and the Transmission Control Module -J217-: 02 - replace control module/Mechatronic (Repair Group 34).

4 - Replacing the dual clutch, replacing the transmission control module -J217-, repairing the transmission, replacing the components in the transmission: 02- Basic Setting (Rep.-Gr. 34).

1. Replacing the shift mechanism function unit.

Note

Shift Mechanism Function Unit, Removing and Installing, refer to → Chapter "Selector Mechanism, Removing and Installing".

The following steps must be performed after completing this procedure:

- Under Guided Functions in the directory 02 - transmission electronics, select the basic setting (Repair Group 34)"Guided Function".

- Select calibrate drive position sensor -G676 and then follow the instructions given on the Vehicle Diagnostic Tester.

A37-10056

2. Assembly work on the selector lever cable when adjusting the cable.

Note

Adjust the selector lever cable, refer to → Chapter "Selector Lever Cable, Checking and Adjusting".

The following steps must be performed after completing this procedure:

- Under Guided Functions in the directory 02 - transmission electronics, select the basic setting (Repair Group 34)"Guided Function".

- Select calibrate drive position sensor -G676 and then follow the instructions given on the Vehicle Diagnostic Tester.

A34-10994

3. Replacing the S tronic Transmission Mechatronic -J743- and Transmission Control Module -J217-

Note

Direct Transmission Mechatronic -J743-, Removing and Installing, refer to → Chapter "Mechatronic, Removing and Installing".

The following steps must be performed after completing this procedure:

- Select Guided Functions in the directory 02 - transmission electronics and the replace control module/Mechatronic (Repair Group 34)"Guided Function" and then follow the instructions given on the Vehicle Diagnostic Tester.

A34-10312

4. Replacing the dual clutch.

Note

Dual clutch, removing and installing, refer to → S tronic Transmission Internal Components; Rep. Gr.30; Clutch; DSG Clutch, Removing or → S tronic Transmission Internal Components; Rep. Gr.30; Clutch; Dual Clutch, Installing.

The following steps must be performed after completing this procedure:

- Under Guided Functions in the directory 02 - transmission electronics, select the basic setting (Repair Group 34)"Guided Function".

- Select the basic setting adapt clutch slip points and then follow the instructions given on the Vehicle Diagnostic Tester.

A30-10198