Rear Seat Back Cover

Components and Component Location

Component Location

[Second Row Seat Assembly for 7-Passenger]

[Second Row Seat Assembly for 8-Passenger]

[Third Row Seat Assembly]

Repair Procedures

Replacement

When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components. Wear gloves to avoid cutting your hands.

1. 1
   Remove the second row seat assembly. (Refer to Rear Seat - "Rear Seat Assembly")
2. 2
   Loosen the mounting screw and remove the rear seat slide handle (A).

   

3. 3
   Loosen the mounting screws and remove the rear seat slide outer cover (A).

   

4. 4
   Press the stopper pin and disconnect the rear seat slide connector (A).

   

5. 5
   Remove the rear seat outer cover (A).

   

6. 6
   Loosen the mounting screw and remove the rear seat inner cover (A).

   

7. 7
   Remove the rear seat headrest (A).

   

8. 8
   Remove the rear seat armrest cover (A), loosen the mounting bolts, and remove the rear seat armrest (B).

   

9. 9
   Remove the rear seat lower guard (A).

   

10. 10
    Using a flat-blade screwdriver, remove the child anchor cover (A) and the seat back rear cover ring (B).

    

11. 11
    Remove the rear seat back lower guard (A).

    

12. 12
    Remove the rear seat back assembly mat (A).

    

13. 13
    Using a flat-blade screwdriver, remove the rear seat back folding switch (A).

    

14. 14
    Press the stopper pin and separate the rear seat back folding switch (A).

    

15. 15
    Using a flat-blade screwdriver, remove the rear seat back protective trim (A) and the rear seat back rear panel cover (B).

    

16. 16
    Remove the rear seat ventilation duct (A).

    

17. 17
    Using a flat-blade screwdriver, remove the rear seat back inner trim protector (A).

    

18. 18
    Press the stopper pin and remove the rear seat headrest guide (A).

    

    

19. 19
    Remove the hook-and-loop fastener (A) and the ring clips (B) inside the rear seat back rear cover. Remove the rear seat back rear cover (C).

    

20. 20
    To install, reverse the removal procedure.

    Before installation, evenly tighten the cover (C) with the ring clip (B) to prevent wrinkles on the cover.

(LH)

When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components. Wear gloves to avoid cutting your hands.

1. 1
   Remove the second row seat assembly [LH]. (Refer to Rear Seat - "Rear Seat Assembly")
2. 2
   Remove the rear seat lower guard (A).

   

3. 3
   Loosen the mounting screw and remove the rear armrest rear cover (A).

   

4. 4
   Loosen the mounting bolt and remove the rear armrest (A).

   

5. 5
   Press the stopper pin (A) and remove the rear armrest trim (B).

   

6. 6
   Press the stopper pin and remove the rear seat headrest (A).

   

7. 7
   Remove the mounting bolts and nuts, and remove the rear armrest bracket (A).

   

8. 8
   Loosen the mounting screws and remove the rear armrest rear panel (A).

   

9. 9
   Using a screwdriver or a remover, remove the rear seat outer cover (A).

   

10. 10
    Using a screwdriver or a remover, remove the rear center seat belt cover (A).

    

11. 11
    Loosen the rear center seat belt bolt (A).

    Tightening Torque: 44.1–59 N·m

    

12. 12
    Using a remover, remove the child anchor cover (A).

    

13. 13
    Remove the rear seat lower guard (A).

    

14. 14
    Press the stopper pin and disconnect the seat heater connector (A).

    

15. 15
    Press the hooks and remove the headrest guide (A).

    

    

16. 16
    Remove the rear seat back assembly cover (A) from the rear seat frame.

    

17. 17
    After removing the hook-and-loop fastener (A) and ring clips (B) inside the rear seat back cover, remove the rear seat back cover (C).

    

18. 18
    To install, reverse the removal procedure.

    Replace all damaged clips.

(RH)

Wear gloves to protect your hands.

When prying with a flat-blade screwdriver, wrap the tip with protective tape to prevent damage to the surrounding parts. Use a plastic trim removal tool to remove the interior trim parts to prevent damage to the surface. Be careful not to bend or scratch the trim and panels.

1. 1
   Remove the second row seat assembly [RH]. (Refer to Rear Seat - "Rear Seat Assembly")
2. 2
   Press the stopper pin (B), then remove the rear seat headrest (A).

   

3. 3
   Remove the rear seat lower guard (A).

   

4. 4
   Loosen the mounting screw and remove the rear seat guard inner cover (A).

   

5. 5
   Press the lock pin and disconnect the connector (A).

   

6. 6
   Using a screwdriver or a remover, remove the rear seat outer cover (A).

   

7. 7
   Using a remover, remove the child anchor cover (A).

   

8. 8
   Remove the rear seat back lower guard (A).

   

9. 9
   Press the stopper pin and disconnect the heater connector (A).

   

10. 10
    Using a screwdriver or remover, remove the rear seat back cover (A).

    

11. 11
    Press the hooks and remove the headrest guide (A).

    

    

12. 12
    Using a remover, remove the rear seat back folding switch (A).

    

13. 13
    Press the stopper pin and disconnect the rear seat back folding switch connector (A).

    

14. 14
    Remove the rear seat back assembly cover (A) from the rear seat frame.

    

15. 15
    After removing the hook-and-loop fastener (A) and ring clips (B) inside the rear seat back cover, remove the rear seat back cover (C).

    

16. 16
    Install in the reverse order of removal.

    Replace all damaged clips.

When removing with a flat-blade screwdriver or puller, wrap the tool with protective tape to prevent damage to the components. Wear gloves to avoid cutting your hands.

1. 1
   Remove the third row seat assembly. (Refer to Rear Seat - "Rear Seat Assembly")
2. 2
   Loosen the mounting bolts and nuts, and remove the third row seat assembly main frame (A).

   

3. 3
   Press the stopper pin and disconnect the third row seat mounting connectors [RH] (A).

   

4. 4
   Remove the mounting bolts and remove the third row seat cushion frame (A).

   

5. 5
   Press the button (A) and remove the third row seat headrest (B).

   

6. 6
   Using a remover, remove the child anchor cover (A) and return it to the hook (B).

   

7. 7
   Remove the lower ring (A) of the third row seat back trim.

   

8. 8
   Using a flat-blade screwdriver, remove the third row seat back lower protector (A).

   

9. 9
   Open the side zipper (A) on the third row seat back [LH].

   

   [RH]

   

10. 10
    Using a remover, remove the headrest cover (A).

    

11. 11
    Press the stopper pin and remove the rear seat headrest guide (A).

    

    

12. 12
    Remove the hook-and-loop fastener (A) and ring clips (B) inside the rear seat back rear cover. Remove the third row seat back rear cover (C).

    

13. 13
    To install, reverse the removal procedure.

    Before installation, evenly tighten the cover (C) with the ring clip (B) to prevent wrinkles on the cover.