Repair Procedures

DEPOSIT

1. 1
   Disconnect the negative (-) battery terminal.
2. 2
   Remove the steering wheel. (Refer to Steering System - "Steering Wheel")
3. 3
   Remove the upper and lower steering column covers after loosening the screws. (Refer to Body - "Steering Column Cover")
4. 4
   Inspect the clock spring. (Refer to Restraints - "Driver Airbag Module and Switch (DAB)" - rotating)

   

5. 5
   Disconnect the multifunction switch connector (A).

   

6. 6
   Remove the multifunction switch (A) after loosening the screws.

   

REMEDY

1. 1
   Install the multifunction switches.
2. 2
   Install the clock spring.
3. 3
   Install the upper and lower steering column covers.
4. 4
   Install the steering wheel.
5. 5
   Connect the negative (-) battery terminal.

Inspection

1. 1
   Check the continuity between the terminals at each switch position as shown below.

   

   [LHD]

   With switch	Switch Position	Switch Terminal	Resistance (Ω, ±3.5%)
   FRONT WIPER INTERMITTENT	FOG	1,9	330
   	OFF		∞
   	Intermittent (AUTO)		800
   	Down		1800
   	High		5700
   REAR WIPER INTERMITTENT	OFF	9-16	∞
   	Down		910
   	High		2910
   Intermittent Wiper Volume	Level 1	7~9	330
   	Level 2		690
   	Level 3		1310
   	Level 4		2610
   	Level 5		7310
   Fog Light Switch	OFF	9.10	∞
   	Front Fog Lamps		910
   	Rear Fog Lamp		2910
   Turn Signal Switch	OFF	9.12	∞
   	LEFT		910
   	LAW		2910
   High/Low Beam Switch	OFF	9~13	∞
   	PASSING		910
   	Headlamps		2910
   Switch	OFF	9~14	∞
   	AUTO/DRL		680
   	Tail Light		1680
   	Headlamps		5580

   
   [RHD]

   With switch	Switch Position	Switch Terminal	Resistance (Ω, ±3.5%)
   FRONT WIPER INTERMITTENT	FOG	3-16	330
   	OFF		∞
   	Intermittent (AUTO)		800
   	Down		1800
   	High		5700
   REAR WIPER INTERMITTENT	OFF	9-16	∞
   	Down		910
   	High		2910
   Intermittent Wiper Volume	Level 1	2.16	330
   	Level 2		690
   	Level 3		1310
   	Level 4		2610
   	Level 5		7310
   Fog Light Switch	OFF	14~16	∞
   	Front Fog Lamps		910
   	Rear Fog Lamp		2910
   Turn Signal Switch	OFF	13~16	∞
   	LEFT		910
   	LAW		2910
   High/Low Beam Switch	OFF	12~16	∞
   	PASSING		910
   	Headlamps		2910
   Switch	OFF	11 to 16	∞
   	AUTO/DRL		680
   	Tail Light		1680
   	Headlamps		5580

2. 2
   In the body electrical system, a fault can be quickly diagnosed using the Global Diagnostic System (GDS). The GDS provides the following information.

   1. Self-diagnosis: checks for malfunctions and the number of codes (DTC)
   2. Current data: checking the input/output status of the system
   3. Operation check: checks the operating conditions of the system
   4. Additional function: controls other functions, including additional system setup and zero point adjustment
3. 3
   Select "Vehicle Model" and "Body Control Module (BCM)" to check the vehicle with the tester.
4. 4
   Select the "Current Data" menu to check the current status of inputs and outputs.