Instrument Cluster Repair Procedures

Removal

1. 1
   Disconnect the negative (-) battery terminal.
2. 2
   Remove the cluster fascia panel. (Refer to Body - Instrument Panel)
3. 3
   Remove the cluster (A) after removing the screws.

   

4. 4
   Disconnect the cluster connector (A) from the cluster.

   

Installation

1. 1
   Connect the cluster connector.
2. 2
   Install the cluster assembly.
3. 3
   Install the cluster fascia panel.
4. 4
   Connect the negative (-) battery terminal.

   After replacing the cluster with a new one, perform the "Variant Coding" procedure.

Inspection

1. 1
   Checkpoint (Warning Lamp)

   NO	Reference Symbol	Color	Name	Input Signal	Signal Control (Unit/Sensor)	Checkpoint
   1		Green	Turn Left	C-CAN	Road	CAN Line Malfunction
   2		Green	Turn Right	C-CAN
   3		Green	Front Fog	C-CAN	Road	CAN Line Malfunction
   4		Blue	High Beam	C-CAN	Road	CAN Line Malfunction
   5		Green	Low Beam	C-CAN	Road	CAN Line Fault
   6		Green	Rear Lamp	C-CAN	Road	CAN Line Fault
   7		Green	Cruise	C-CAN	VCU	CAN Line Malfunction
   8		Green	SET	C-CAN	Road	CAN Line Malfunction
   9		Red	Seat belt	C-CAN	Road	CAN Line Malfunction
   10		Red	Air Bag	C-CAN	ACU	CAN Line Malfunction
   11		Yellow	Liftgate open	C-CAN	Road	CAN Line Malfunction
   12		Red	Door Open	C-CAN	BGWAY	CAN Line Malfunction
   13		Yellow	Immobilizer	C-CAN	Road	CAN Line Malfunction Wiring Fault
   14		Yellow	ABS	C-CAN	ESC	CAN Line Malfunction
   15		Yellow	ESC	C-CAN	TCS	CAN Line Malfunction
   16		Yellow	OFF	C-CAN	TCS	CAN Line Malfunction
   17		Yellow	SCP	C-CAN	SCP	CAN Line Malfunction
   18		Red	Parking Brake	C-CAN	Road TKS AHB	CAN Line Malfunction
   19		Red	Battery Charge	C-CAN	HCU	Wiring Fault
   20		Yellow	Check Engine	C-CAN	Emergency Call	CAN Line Malfunction
   21		Yellow	Low Washer	Hard Wire	Water Level Sensor	Wiring Fault
   22		Green	Active ECO	C-CAN	VCU	CAN Line Malfunction Wiring Fault
   23		Red	MDPS	C-CAN	MDPS	MSPP Module Failure CAN Line Malfunction
   24		Green	READY	C-CAN	VCU	CAN Line Malfunction
   25		Green	EV battery charging	Hard wired + C-CAN	BCM	CAN Line Malfunction Wiring Fault
   		Red			Emergency Call	CAN Line Malfunction
   26		Yellow	EV System	C-CAN	VCU, MCU, BMS, LDC, FATC, OBC	CAN Line Malfunction
   27		Yellow	Turn Off	C-CAN	VCU	CAN Line Malfunction
   28		Yellow	DBO	C-CAN	ABS	CAN Line Malfunction
   29		Yellow	Low power	C-CAN	VCU	CAN Line Malfunction
   30		Yellow	EPB	C-CAN	EPB	CAN Line Malfunction

2. 2
   TR Switch (Sensor)

   No.	Name	Input Signal	Signal Control (Unit/Sensor)	Checkpoint
   1	Speedometer	C-CAN	MCU	CAN Line Fault
   2	SOC sensor	C-CAN	BCM	CAN Line Fault
   3	Power and charge indicator	C-CAN	VCU	CAN Line Fault

3. 3
   Check the specified value of the cluster connector in the specified condition.

   No.	Description	Input, output	Communication	Value (V)	Specified conditions
   1	GND_Signal3	Input	Hardware	Above 5 V	Ignition ON,
   2	BATT(-)_OUT-	Output	Hardware	Below 1 V	Ignition ON, tail switch ON, dimmer at maximum.

Instrument Cluster Description and Operation

Component Description and Features 1. Power and Charge Gauge (1) Displays the level of economical driving by determining the driver's operating status according to the vehicle drive mode. Condition...

Troubleshooting

Troubleshooting Malfunction Item / Symptom / Check Point / Related Parts. Display: OLED-LCD does not display. 1) Check the connection between connectors. 2) Check the battery (+), ignition and ground wiring...

Additional information:

Kia Soul EV (PS EV) 2015-2020 Service Manual: Hood Latch Repair Procedures

Replacement 1. Remove the liftgate handle (A). 2. Loosen the bolts and clips securing the front bumper upper cover. 3. Carefully lift the front bumper upper cover. 4. Loosen the screw (B) and remove the front bumper upper cover (A). 5. Loosen the bolts, then remove the hood latch...

Kia Soul EV (PS EV) 2015-2020 Service Manual: On-Board Charger (OBC) Repair Procedures

Removal • Be sure to read and follow the "General Safety Information and Caution" before performing any work on the high voltage system. Failure to follow safety instructions may result in serious electrical injury. • Be sure to...